Introduction of pressure transmitter sensor:
BP155 pressure transmitter sensor is used to control the oil pressure of the brake system with the
oil pressure booster. It detects the pressure of the reservoir, the
closing or disconnecting signal of the output oil pump, and the
abnormal oil pressure alarm. The change of pressure is detected by
the ceramic diaphragm and converted into an electrical signal for
external output.
Product Features of pressure transmitter sensor:
1. Wide measuring range, stainless steel structure, diverse
pressure interface forms.
2. Compact and lightweight design.
3. Zero and full-scale adjustable.
4. High precision, all stainless steel structure.
Applications of pressure transmitter sensor:
1. Pressure measurement of non-corrosive gases and liquids with
316L stainless steel.
2. Applied in the marine and aviation industries.
3. Used in industrial on-site processes such as petroleum,
chemical, metallurgy, power generation, and hydrology.
4. Utilized in hydraulic and pneumatic control systems.
| Performance Parameters of pressure transmitter sensor: |
|---|
| Measurement Range | 0kPa ~ 200kPa…5MPa |
|---|
| Pressure Type | Gauge Pressure, Absolute Pressure, Sealed Pressure |
|---|
| Overload | ≤ 1.5 times of the rated range |
|---|
| Accuracy @ 25ºC | ±0.25% (Typical) ±0.5% (Maximum) |
|---|
| Repeatability& Hysteresis | 0.02%F.S(Typ.) 0.05%F.S(Max.) |
|---|
| Long-Term Stability | ±0.1%F.S/Year(Typ.) ±0.2%F.S/Year(Max.) |
|---|
| Zero Point Temperature Drift | ±0.02%F.S/ºC(≤100KPa) ±0.01%F.S/ºC(>100KPa) |
|---|
| Full Scale Temperature Drift | ±0.02%F.S/ºC(≤100KPa) ±0.01%F.S/ºC(>100KPa) |
|---|
| Frequency Response | 2.4Khz |
|---|
| Compensation Temperature | 0-70ºC(≤10mpa,customizable) |
|---|
| Operating Temperature | -20ºC~80ºC |
|---|
| Storage Temperature | -40ºC~120ºC |
|---|
| Vibration | 10g,55Hz ~ 2kHz |
|---|
| Housing Material | 304,316L |
|---|
| Diaphragm Material | 316L |
|---|
| Insulation Resistance | 100MΩ 100VDC |
|---|
| Explosion-proof Rating | Ex ia IIC T6 Ga |
|---|
| Protection Rating | IP65 |
|---|
| O-Ring Seal | Fluoro rubber |
|---|
| Output Signal | Supply Voltage | Output Type |
| 0.5~4.5V | 5VDC |
3 wire |
1. When selecting the product, please ensure that the tested medium
is compatible with the contact part of the product.
2. When placing an order, please note that explosion-proof products
do not include digital display heads.
3. To ensure reliable operation of the product, you are advised to
install lightning protection devices onsite and ensure that the
product and power supply are grounded reliably.
5. The rated operating temperature range of fluorine rubber O-ring
is -20℃~ 250℃. When the product operating temperature is lower than
-20℃, EPDM O-type sealing ring should be selected.
6. By default, there is no cable and the other end of the plug-in,
if necessary, there are three materials to choose from. Unless
otherwise specified, polyethylene cable material can be used. If
you need a different cable material, please specify it in the order
form.
7. In case of special requirements such as strong vibration,
instantaneous impact force, strong electromagnetic or RF
interference, please inform and indicate in the order.
| Order Guide |
| BP15X | Analog Pressure Transmitter |
| Code | Outline Construction |
| 5 | Packard plug | 6 | Sealed Direct Output Cable 1.5 meters |
| 7 | Mini Hirschmann Connector | 8 | Large Hirschmann Connector |
| Measurement Range | 0kPa ~ 200kPa…5MPa |
(0-X)Kpa
or MPa | X: Indicates the Actual Measuring Range |
| Code | Power Supply |
| D1 | 24VDC |
| D2 | 5VDC |
| D3 | Other |
| Code | Output Signal | |
S1 | 4~20mADC | S5 | 0~20mADC |
S2 | 1~5VDC | S6 | 0~10VDC |
S3 | 0~5VDC | S7 | 0.5~4.5VDC |
S4 | 0~10mADC | | |
| Code | Pressure Connection |
| J1 | M20×1.5 |
| J2 | G1/2 |
| J3 | G1/4 |
| J4 | 7/16-20UNF |
| J5 | Others(¢50.4 Flange) |
| Code | Electrical Connection |
| B1 | Hirschmann |
| B2 | PG7 |
| B3 | Cable Sealed Outlet 1.5 meters |
| B4 | Other |
| Code | Pressure Type |
| G | Gauge Pressure |
| A | Absolute Pressure |
| S | Sealed Reference Pressure |
FAQ
1.Q: How long is the delivery?
-- Mostly within 3-10days
2.Q:Can I get a sample?
-- Sure, contact our sales please
3.Q:What is your MOQ?
-- 1pcs
4.Q: How about warranty time?
-- 12-18months
5.Q: Are you manufacture?
-- Yes we are manufacture for nearly 30years for pressure sensor
and transmitter.
6.Q:How do you control your quality ?
-- We have EPR system .we control from parts, process, testing,
packing ,retesting.
7.Q: Do you have test report for each product?
-- Yes,we have test report for each product.
8.Q: Can you customize product for us according to our required
specifications?
-- Yes,we are OEM manufacturer,we could customize products
according to your required specifications.
Every Sensor will be tested two times before reach you, after that
sport test for the third time. Make sure about the quantity.Welcome
to order our products
