WL-0163 Multi-Functional Nano Protective Lacquer
The main structure of WL-0163 is “Inorganic Siloxane-based
alcohol-soluble Resin.” The main chemical bonds of WL-0163
are[-O-Si-O-]bonds which has the strongest chemical bonding
comparing with other carbon-containing chemical bonds in organic
resins such as[-C-O-]bond, [-C-C-]bond, and[-C-H-]bond, so
WL-0163can produce excellent features of chemical resistance,
solvent resistance, heat resistance(~600〫C), high hardness(2-8H),
abrasion resistance, and excellent weathering resistance which can
protect the floor to get rid of the damage from the ultraviolet
rays.
Because the particle size of the resin itself is only 50um which
makes WL-0163has the feature of great penetration to get into the
substrate and create “Chemical Cross-linking Bond” to react with
the substrate of concrete, stones, ceramic tiles, and woods to form
the structure of “Nano-Film” with high adhesion on the surface of
the substrate. The “Nano-Film” can make the concrete own the
effects of being long-acting waterproof, stain-resistant,
damp-proof, mildew-proof, anti-chemical, and non-yellowing.
WL-0163 has excellent self-cleaning and stain-resistant effects.
This is because the structure of the coating film is made by
nanotechnology, which makes WL-0163have long-lasting “Lotus effect”
to extend the service life of concrete, stones, ceramic tiles, and
woods. Not to say to reduce the cost of the maintenance.
Applicable Scope
1. The sealer for the concrete treated by the densifier
2. The protective treatment for the architectural concrete, the
concrete, and the pebble wash.
3. The protective treatment for the water pressure resistance
toward the ditches between the ceramic tiles in the kitchens and
the bathrooms.
4. The treating agent for the efflorescence on the walls and the
leak preventer for the voids in the concrete.
5. The protective curing agent for natural stones, stone artifacts,
and the gems
6. The special brightening agent for the ceramic tiles outdoor
7. The protective curing agent used to maintain the historic
monuments and temples.
Construction Methods
● Clean up the substrate before applying the agent of WL-0163 (the
moisture content percentage of the substrate must be below 10%)
● There are two agents in this product set, one is the main agent,
and the other is the densifier. The dilution ratio of the main
agent to the densifier is 100 : 1. You must apply the diluted
WL-0163 on the substrate within 48 hours after mixing the two
agents together. It will take 1-4 hours for the surface of the
substrate to get dry after applying WL-0163on it. After applying
WL-0163on the substrate, you must wait at least 24 hours to make it
efficient, and never let the substrate applied with
WL-0163contacted with a lot of water in 72 hours.
● You can roll, paint, brush, or spray WL-0163on the substrate
depending on what kind of substrate you are going to apply WL-0163
on.
● You can use industrial heat guns or jet-burners to heat the
substrate applied with WL-0168 to raise up the physical property of
the substrate.
● Before applying this product, you can make a trial on the
inconspicuous part of the substrate first. Apply WL-0163on the
substrate thoroughly if the trial result meets your requirements.
The comparison between WL-0168and normal organic coating agent
| Item | WL-0163 | Organic coatings |
| Heat Resistance | non-yellowing till 600〫C | yellowing above 200〫C |
| Aging and UV Resistance | Great | Bad |
| Pencil Hardness | 2H-8H, depending on baking temperature | 3H at most |
| Marresistance | Great | Normal |
| Oil and Solvent Repellence | Great | Bad |
| Stain Resistance | Great | Bad |
| Corrosion Resistance | Great | Good |
| Coating Stableness | Over 10 years | Cracked after 3-5 years |
| Chemicals Resistance | Great | Limited |
