Material Introduction
The high-frequency, ceramic-filled PTFE laminates of Rogers
RO3003G2 are an extension of Rogers' industry-leading RO3003
solutions. The development of RO3003G2 laminates is based on
industry feedback, with a special focus on addressing the next
generation needs for millimeter wave automotive radar applications.
The incorporation of an optimized resin and filler content, along
with the utilization of Very Low Profile ED copper provides a
reduced insertion loss. This characteristic makes RO3003G2
laminates well-suited for implementation in Advanced Driver
Assistance Systems (ADAS) such as adaptive cruise control, forward
collision warning, active braking, and lane change assist.
Features
1. The dielectric constant of 3.00 at 10 GHz and 3.07 at 77 GHz.
2. Very Low Profile (VLP) ED copper.
3. Homogeneous construction incorporating VLP ED copper and reduced
dielectric porosity.
4. Enhanced filler system.
Benefits
1. Best-in-class performance for insertion loss.
2. Minimize variation in dielectric constant in the finished PCB.
3. Enable the trend towards using smaller diameter vias; Enhanced
filler system using small rounded particles
4. Global manufacturing footprint.
Our PCB Capability (RO3003G2 laminates)
| PCB Material: | Ceramic-filled PTFE Laminates |
| Designation: | RO3003G2 |
| Dielectric constant: | 3 |
| Dissipation factor | 0.0011 |
| Layer count: | Single Sided, Double Sided, Multi-layer PCB, Hybrid PCB |
| Copper weight: | 1oz (35µm), 2oz (70µm) |
| Dielectric thickness | 5mil (0.127mm), 10mil (0.254mm) |
| PCB size: | ≤400mm X 500mm |
| Solder mask: | Green, Black, Blue, Yellow, Red etc. |
| Surface finish: | Immersion gold, HASL, Immersion silver, Immersion tin, ENEPIG, OSP, Bare copper, Pure gold etc.. |
Typical Applications
1. Adaptive cruise control
2. Forward collision warning
3. Active brake assist
4. Lane change assist
5. Traffic jam pilot
6. Parking pilot
7. Blind spot detection
RO3003G2’s Data Sheet
| PROPERTY | RO3003G2 | Direction | Unit | condition | Test Method |
| Dielectric Constant, er Process | 3.00 ± 0.04 | Z | - | 10 GHz 23°C | IPC-TM-650
2.5.5.5
Clamped Stripline |
| Dielectric Constant, er Design | 3.07 | Z | - | 77 GHZ | Differential Phase
Length Method |
| Dissipation Factor, tan d | 0.0011 | Z | - | 10 GHz 23°C | IPC-TM-650
2.5.5.5 |
| Thermal Coefficient of er | -35 | Z | ppm/°C | 10 GHz
-50 to 150°C | IPC-TM-650
2.5.5.5 |
| Dimensional Stability | -0.16
-0.14 | X
Y | mm/m | Method C | IPC TM-650 2.2.4 |
| Volume Resistivity | 1.4 x 109 | - | MΩ•cm | COND A | IPC 2.5.17.1 |
| Surface Resistivity | 2.6 x 108 | - | MΩ | COND A | IPC 2.5.17.1 |
| Tensile Modulus | 378
396 | X
Y | ksi | 23°C | ASTM D638 |
| Moisture Absorption | 0.06 | - | % | D48/50 | IPC-TM-650
2.6.2.1 |
| Specific Heat | 0.73
0.83 | Z | J/g/K | 0°C
50°C | ASTM E1269-11 |
| Thermal Conductivity | 0.43 | Z | W/m/K | 50°C | ASTM D5470 |
| Coefficient of Thermal Expansion | 16
17
18 | X
Y
Z | ppm/°C | 23°C/50% RH | IPC-TM-650 2.4.41 |
| Td | 500 | - | °CTGA | - | ASTM D3850 |
| Density | 2.15 | - | gm/cm3 | 23°C | ASTM D792 |
| Copper Peel Strength | 12.0 | - | lb/in | 1/2 oz. EDC
After Solder Float | IPC-TM-2.4.8 |
| Flammability | V-0 | - | - | - | UL 94 |
| Lead Free Process Compatible | YES | - | - | - | - |
