Modular Design Q345B Steel Rack And Pinion Elevator
Rack And Pinion Elevator Main Features
1. construction elevator is a kind of elevator driven by rack and
pinion, mainly used for people and goods transportation of
high-rise building construction.This kind of elevator can be easily
installed and disassembled by itself, and can be raised as the
building grows.Construction lifts with single cage and double cage:
single-cage lifts become double-cage lifts when a cage and other
components are added.
2. high-speed frequency conversion construction elevator.The
maximum operating speed can be up to 96 meters per minute, using
800×800×1508 standard section, for high-rise construction sites can
save a lot of time to improve work efficiency, and more stable and
reliable.
3. Inclined construction elevator.It is especially suitable for
Bridges, towers and other small and large buildings with Angle, the
maximum tilt Angle can reach 9°, it is running up the inclined
plane of the building, further ensure the smooth operation of the
construction elevator, the length of the attachment point is
consistent and convenient for installation.
4. The standard section is available in 650×650×1508 and
800×800×1508 models.
Rack And Pinion Elevator Design
It is the truly modular rack and pinion hoist design, so the
elevator drive devices and cars are generic and interchangeable.
Multiple choice of construction lifts car doors or ramps is
available.
The modular and standardizing system makes the Kangbo construction
elevators be flexible, efficient, safe, productive, low energy
consumptive and ownership cost, making them the best choice for
both construction and rental companies.
Rack And Pinion Elevator Technical Data
| Technical Data | KP-B01 |
| Payload capacity | 1,000 kg |
| Lifting speed | 0–54 m/min. |
| Max. lifting height | 250/400 m* |
| Cage width (internal) | 1.5 m |
| Cage length (internal) | 3.2 m |
| Cage height (internal) | 2.35 m |
| Motor control | FC control |
| Engine power | 2x15 kw |
| Gearbox | KANGBO make Helical reducer |
| Safety device type | centrifugal brake |
| Power supply range | 380–500 V, 50 or 60 Hz, 3 phase |
| Type of mast | square column 650*650 mm with bolted rack |
| Length mast section | 1.508 m |
| Rack module | 8 |
| * Increased lifting height on request. 250 m with step-up
transformer only. 400 m with step-up/step-down transformer. |
| Standard Configuration |
| Cage Internal Size | 3.2(L)*1.5(W)*2.35(H) Meters | Perforated Galvanised Cold Roll Steel Plate |
| Cage Frame | Optimized and Strengthened Structure | Q345B Steel |
| Cage Paint | Yellow | Sandblasting and Painted |
| Cage Entry Door | Vertical Sliding | Galvanised Perforated Cold Roll Steel Plate |
| Cage Exit Door | Vertical Sliding/Flap Type | Galvanised Perforated Cold Roll Steel Plate |
| Driver's Cabin | Excluded or Included as per users' requests | |
| Motor Make | Zhangjiang make | |
| Gearbox | Kangbo Make Pieli Brand Helical Gearbox | |
| Mast Section | 650*650*1508mm, Φ76mm, δ4.5mm | Q345B Steel, Painted |
| Rack | 40*60*1508mm, 8 Modulus. | |
| Tie-in | Type II, 2900-3400mm; Every 9 m one set; | Q345B Steel, Painted |
| Or as per users request | |
| Safety Device | SAJ4.0-1.2 | |
| Ground Enclosure | | Galvanised Cold Roll Steel Plate |
| Enclosure Door | Double Hinge Side Open Door | Perforated Galvanised Cold Roll Steel Plate |
| Power Supply | Cable & Cable Drum | Galvanised Cold Roll Steel Plate |
| Over Load Protect | Included | |
| Optional Configuration |
| Mast Section | 650*650*1508mm, Φ76mm, δ4.5mm | Q345B Steel, Galvanised |
| Power Supply | Slide Contact Line System (Busbar) | |
| Floor Selection | Multi-functional Control System (Floor selector, Automatic Landing,
Error Detection and Display, etc.) |
