SZG-500L steam heater small rota-cone vacuum dryer with sintered
filter
Small Rotary Cone Vacuum Drying Equipment SZG-500L Steam Heater
With Sintered Filter
Enamel or titanium tank for special matrial can be choosed.
Principle of Working
SZG-500L steam heater small rota-cone vacuum dryer with sintered
filter has double cone rotating tank. Under the state of vacuum
inside the tank, pass steam or hot water into its jacket for
heating. The hot amount can contact with the damp raw material
through its inner wall. The vaporized steam when the damp raw
material absorbed heat can be pumped out through vacuum exhaust
pipe. Because its inner of tank is in the state of vacuum and the
raw material is turned over all the time caused by the rotating of
tank, the dry speed of raw material is quickened and dry efficiency
is raised too and the purpose of uniform dry can be raised.
| Optional Features : |
l Option for advance PLC Controls with HMI touch screen.. l Option for Flame Proof Electrical. l Option for lump breaker. l Option for condenser, Receiver & Cyclone for solvent recovery. l Option for heating media steam/ hot water / hot oil. |
Application
SZG-500L steam heater small rota-cone vacuum dryer with sintered
filter is suitable for
1. Material that cannot undertake high temperature.
2. Material that is easy to oxidize.
3. Material that do not permit to destruct.
4. To recover material with residual volatile.
5. Material with vigorous irrelative and toxicity.
6. Biology products and mine.
7. Dry raw materials of pharmaceutical industry, chemical industry,
foodstuff industry, dyestuff industry and biochemistry at low temp
etc.
Technical Parameters
| Model | SZG100 | SZG350 | SZG500 | SZG-7500 | SZG1000 | SZG1500 | SZG2000 | SZG3500 | SZG5000 |
| Volume (litre) | 100L | 350L | 500L | 750 | 1000L | 1500L | 2000L | 3500 | 5000 |
| Charging volume (L) | 50 | 175 | 250 | 375 | 500 | 750 | 1000 | 1750 | 2500 |
| Loading weight(kg) | 40 | 120 | 200 | 300 | 400 | 600 | 800 | 1000 | 1800 |
| Heating area(m2) | 1.16 | 1.5 | 2 | 2.63 | 3.5 | 4.61 | 5.58 | 7.5 | 13.8 |
| Rotating speed(rpm) | 3~13 |
| Motor power | 0.75 | 1.1 | 1.5 | 2.2 | 3 | 4 | 5.5 | 7.5 | 15 |
| Rotating height | 1750 | 2100 | 2250 | 2490 | 2800 | 2940 | 2990 | 3490 | 4200 |
| Desigh pressure insider the tank: ---0.1~0.15Mpa |
| Desigh pressure inside the jacket: ≤0.3Mpr |
| Total weight (Kg) | 650 | 900 | 1200 | 1450 | 1970 | 2280 | 2500 | 2700 | 2900 |
Notes : 1. The above-mentioned parameters are calculated based on
material density 0.6g./cm3.if for reference only.
2. For raw material, if its volume has great change before and
after dry, then its filling coefficient may be increased or
decreased suitably.
3. Speed adjusting motor of 0~6rpm for optional according to user’s
requirement.
The following aspects should be point when order
If certificate for pressure vessel is requirement, please point
out.
if glass lining for interior surface is requirement, please point
out.
If the material is explosive, or flammable, the calculation should
be made according to trial result.1. If material has larger
specific weight, it shall be noted upon placing the order.
