Inclined Flexible Auger Conveyor Continuous Transportation
Equipment Smiple Structure
Characteristics
The screw conveyor is relatively simple and the cost is low;
Reliable work, simple maintenance and management; The size is
compact, the section size is small, the occupation area is small;
It can realize sealed transportation, which is beneficial to the
transportation of materials that are easy to fly, hot and smelly,
and can reduce the pollution to the environment. Easy to load and
uninstall. The horizontal screw conveyor can be loaded and unloaded
at any point on its transmission line;The unit energy consumption
is large;The material is easy to grind and wear in the process of
transportation, and the wear of spiral blade and material groove is
also more serious
U Trough screw conveyor is made up of screw part, bearing part and
driving devices. Screw part is supported by both ends of bearing
and middle bearing and driven by driving devices. When the screw
conveyor operate, handling material will come into the feed chute
by inlet, then do axial movement along the chute under the action
of rotate screw until out of the outlet.
U Trough screw conveyor is bulk material handling equipment, it
provides enclosed transfer while moving materials horizontally or
at an angle,it can deliver materials from one or more inlet points
to one or more discharge points. Screw conveyors can be operated
with the flow of material inclined upward. When space allows, this
is a very economical method of elevating and conveying. As the
angle of inclination increases, the capacity of a given unit
rapidly decreases.
Application
U Trough screw conveyor is widely used in building materials,
metallurgy, chemical industry, machinery, light industry, grain and
food industry. U-type screw conveyor is suitable for conveying
powder Shaped, granular, small bulk materials, such as cement, fly
ash, grain, chemical fertilizer, mineral powder, sand, soda and so
on. U-shaped screw conveyor is not suitable for transporting
materials that are easy to deteriorate, sticky and easy to caking.
The working environment temperature of the conveyor is usually-20
°40 °, the temperature of the conveying material is generally 20
°80 °℃, the U-shaped screw conveyor is suitable for horizontal and
small inclination arrangement, and the inclination angle is not
more than 15 degrees. If the tilt angle is too large, the tubular
screw conveyor should be selected.
Technical parameter of Screw Conveyor
| Model | Diameter mm | Pitch mm | Speed r/min | Standard Capacity(m3/h) | Speed r/min | Standard Capacity(m3/h) | Speed r/min | Standard Capacity(m3/h) |
| φ0.45 | φ0.33 | φ0.15 | φ0.45 | φ0.33 | φ0.15 | φ0.45 | φ0.33 | φ0.15 |
| LS200 | 200 | 200 | 100 | 16.9 | 12.4 | 5.6 | 80 | 13.5 | 9.9 | 4.5 | 63 | 10.7 | 7.8 | 3.6 |
| LS315 | 315 | 315 | 80 | 52.9 | 38.8 | 17.6 | 63 | 41.6 | 30.5 | 13.9 | 50 | 33.1 | 24.2 | 11 |
| LS400 | 400 | 355 | 71 | 85.3 | 62.5 | 28.4 | 56 | 67.3 | 49.3 | 22.4 | 45 | 54.1 | 39.6 | 18 |
| LS500 | 500 | 400 | 63 | 133.2 | 97.7 | 44.4 | 50 | 105.8 | 77.6 | 35.3 | 40 | 84.6 | 62.0 | 28.2 |
| LS630 | 630 | 450 | 50 | 188.9 | 138.5 | 63.0 | 40 | 151.1 | 110.8 | 50.4 | 32 | 120.9 | 88.6 | 40.3 |
Selection Conditions
| Material to be processed: _____ | Working environment is indoor or outdoor:________ |
| Handling capacity: ________per hour | Working environment temperature: _______ ℃ |
| Bulk Density: _____t/m3 | Installation form is horizontal or inclined : ________ |
| Conveying distance: ________ | If it is inclined,what is the inclined degree_____° |
| Material size:____mm | Water content:____% |
| Material temperature: _______ ℃ | Working power supply: _____V ______HZ ______PH |
