12m³ Constant Temperature and Humidity Walk-In Environmental Chamber

12m³ Constant Temperature and Humidity Walk-In Environmental Chamber

Complied Standards & Clauses

IEC60068-2-1:2007 “Environmental Testing-Part 2-1: Tests-Test A: Cold, IDT”

IEC60068-2-2:2007 “Environmental Testing-Part 2-1: Tests- Test B-Dry heat, IDT”

IEC60068-2-30:2005 “Environmental Testing-Part 2-30: Tests-Test Db: Damp heat, cyclic (12h+12h cycle) , IDT”

IEC60068-2-78:2012 “Environmental Testing-Part 2-78: Tests-Test Cab: Damp heat, steady state, IDT”

Equipment Overview

Applications: It is used for high and low temperature and damp heat tests on electricians, electronics, machinery, and large parts, semi-finished products, and finished products. Process quality and reliability testing of products, parts, etc. under simulated temperature and humidity conditions.

Test Principle: The heating, humidification and refrigeration system is used to control and change the ambient temperature and humidity in the chamber, simulating the ambient temperature / humidity and alternating procedures required by the testing.

Structure: Adopts closed chamber structure.

Technical Parameters

Control & Operation		PLC and touch screen intelligent control system
Chamber Size		12m3: WDH=3×2×2m Can be customized
Temperature Range (Optional)		Maximum test temperature: 80 ° C, 120 ° C; Minimum test temperature: -60 ° C, -40 ° C, -20 ° C, 0 ° C
Temperature Deviation		≦±2.0℃
Temperature Fluctuation		±0.5℃
Temperature Uniformity		±2℃
Humidity Range		30%〜98%RH
Humidity Deviation		±5.0％RH
Heating Rate		≤2.5°C/min (nonlinear, no load)
Cooling Rate		Average 1.0 ° C / min
Temperature and Humidity Range Icon
System Main Composition
Chamber Body	The inner chamber is made of SUS304# stainless steel plate, rounded shape, smooth, easy for clean
	The outer chamber is made of A3 cold-rolled steel plate electrostatic double-sided spray or SUS304 stainless steel
	Lead hole: inner and outer chambers are equipped with a threading hole with a rubber stopper
	Insulation material: polyurethane foam
	Observation window: double-layer explosion-proof tempered glass door
Heating System	Heating method: electric heating
	High quality nickel-chromium wire electric heater, contactless control (SSR)
Humidification System	Humidification method: external humidification structure
Cooling System	German Bock semi-tight compressor or German BITZER semi-compact compressor
	Non-fluorine environmentally friendly refrigerant R404A R23, in line with environmental regulations, safe and non-toxic.
	Shell and tube condenser (water cooled).
	High-performance fin type automatic load capacity adjustment, long-term use of low temperature and high humidity conditions without frosting.
Control System	Touch screen: Weinview programmable temperature and humidity controller (7 inch 16-bit true color touch screen)
	Temperature control: PID self-tuning, using Class A PT100 platinum resistance sensor
	Function: fixed value test and program test Fixed value test: When the test environment requires only a single temperature and humidity, selecting this mode to set the required temperature, humidity and running time. Program test: When the test environment requires multiple temperatures and humidity, select this mode to set the temperature, humidity and running time of each program. User can set the program running sequence. The program group is up to 100 groups.
Data Storage	With temperature and humidity curve interface, with standard R232 interface or U disk communication interface, the data can be downloaded, and the data changes and processes can be recorded.
Safety Protection	Power-off memory function, phase sequence protection, leakage protection, over-temperature protection, compressor overload protection, water shortage alarm, abnormal protection
Safety Protection Device	Heater air-burning protection switch, heater over current circuit breaker, circulating fan over current overload protection
	Compressor high voltage protection switch, compressor overheat protection switch, compressor over current protection switch
	Under-reverse phase circuit breaker, no-fuse switch, zero-crossing gate fluid power controller
Alarm Indication	When the above protection occurs, the equipment stops running, an audible and visual alarm is issued, and the fault location is displayed on the meter.

Sinuo Testing Equipment Co., Limited established in 2019, but Sinuo has rich experience in manufacturing test euipment, test system and offering overall laboratory construction of electronic and electrical products. Sinuo's main products include electrical vehicle test equipment, battery testing equipment,  electromagnetic compatibility (EMC) test system, environmental testing equipment, fire retardant test equipment, dust-proof waterproof testing equipment and electrical appliances testing equipment. Our products covering electrical vehicle, electric power, communication, electrical appliances and electronic devices industries.

Sinuo has a professional technical research and development team, which is proficient in various international standards such AS IEC, ISO, EN, VDE, BS, AS, ASTM, GB and industry standards such AS MBN LV124, VW-80000. We master physical mechanics, heat, electricity, fluid and other theoretical knowledge in the application of equipment. And continue to focus on industry standard equipment performance optimization, operation simplification and equipment stability and reliability improvement.

Sinuo has two factories in Guangzhou and Dongguan, and cooperates with many research institutions and schools. Our R&D and production capacity are in the forefront. We have authorized agents in South Korea, the United States, South Africa, Egypt, Pakistan, the Philippines and other places, we serve customers BV, CSA, Intertek, SGS, TUV and other internationally renowned testing and certification institutions, local government quality inspection departments and production factories.