AC80V-220V 0-10A 2200W JKBLD2200 110BLS motor Brushless Dc Motor
Driver/controller
| Product Series | Poles No. | Rated Voltage | Rated Speed | Rated Torque | Rated Power | Motor Length |
| 42mm BLDC Motor | 8 | 24v | 4000rpm | 0.0625~0.25N.m | 26~105w | 41~100mm |
| 57mm BLDC Motor | 4 | 36v | 4000rpm | 0.055~0.44N.m | 23~184w | 37~107mm |
| 60mm BLDC Motor | 8 | 48v | 3000rpm | 0.3~1.2N.m | 94~377w | 78~120mm |
| 80mm BLDC Motor | 4 | 48v | 3000rpm | 0.35~1.4N.m | 110~440w | 78~138mm |
| 86mm BLDC Motor | 8 | 48v | 3000rpm | 0.35~2.1N.m | 110~660w | 71~138.5mm |
| 110mm BLDC Motor | 8 | 310v | 3000rpm | 1.65~6.6N.m | 518~2073w | 83~173mm |
| 130mm BLDC Motor | 10 | 310v | 3000rpm | 2.39~11.94N.m | 750~2500w | 115~190mm |
| Above only for representative products, products of special request
can be made according to the customer request. |
Product Overview:
JKBLD2200 brushless DC motor driver is our company's latest
high-tech product for the field of high power motor drive. This
product uses a large-scale integrated circuit to replace the
original hardware. It has higher anti-jamming and fast response
ability. It is suitable for all the three-phase brushless DC motors
with low voltage DC310V and current below 10A. Even if working with
large current, it is still in low temperature.
Main features:
- It has double speed closed current design with low speed torque
andsmooth operation;
- It has high speed output with the maximum speed of 10000rpm / min;
- Speed control mode : analog quantity 0-5V
- It has have EN, DIR signal control side;
- It can output tachometer pulse (optoelectronic isolation, gate output);
- It has over-current, overvoltage, under voltage , overheating,
motor stalling and other protection functions
Electrical Specification:
(1)Environmental Temperature:25℃
| Power supply | AC100V～250V direct current (Capacity according to motor power selection) |
| The maximum input current | Not greater than10A (according to motor and rated load) |
| The maximum power | The maximum is 2200W (over power motor is strictly prohibited) |
| Insulation resistance | General temperature﹥500MΩ |
| Insulation strength | General temperature and pressure 0.5KV,1minitute |
(2)EnvironmentalParameter
| Cooling method | Natural air cooling & forced air cooling |
| Environment | Condition | Avoid dust, oil mist and corrosive gases |
| Temperature | 0℃～+50℃ |
| Humidity | ﹤80%RH,no condensation, no frost |
| Vibration | 5.9m/s2 max |
| Reserved temperature | -20℃～+65℃ |
| Size | 198mmX103mmX86mm |
| Weight | About 1Kg |
Note: Due to dramatic changes in the temperature of the storage
environment, it is easy to form condensation or frost. In this
case, the drive should be placed for 12 hours or more. Until the
drive temperature and ambient temperature is consistent, it can be
on power.
Terminal interface description:
| Function | Mark | Description |
| Indicator light | POWER | If the green power indicator is lighten, it shows that power is
normal. |
| ALM | If the red status indicator is slow flash, it means waiting; Quick
flash means operation; It always lights meaning faults or off-line; |
| Control signal port | +5V1 | Control signal power+( inner power output ) |
| VSP | External speed control signal Control way: By connecting with a potentiometer to change VSP, then
it can complete 0 ~ 100% speed adjustment. The range is 0-5V |
| FG | Motor speed pulse output is measuring the frequency of this signal.
Then converts it into the actual motor speed. |
| DIR | Rotary direction is controlled by high and low electrical level,
motor forward: connected with GND1, motor reversal (anticlockwise)
;without GND1 or connected with +5V, motor forward (clockwise) |
| EN | Connected EN with GND1, motor can work(online status);without
connected,motor can not work(offline status and the red light keep
working) |
Hall control port | +5V2 | + motor’s Hall power |
| HU | Hall sensor signal U phase input |
| HV | Hall sensor signal V phase input |
| HW | Hall sensor signal W phase input |
| GND2 | The motor’s Hall power supply |
| The motor and power port | U,V,W | The motor’s three-phase output signal |
| AC1,AC2 | The input power is AC100V～250V |
General problems
1. How can get it started as soon as possible when you first use
the drive?
After you correctly connect the power cord, the motor line, the
Hall line, the external potentiometer slowly accelerates. After the
motor is turned correctly, you can test the enable, direction and
other functions. If you are unfamiliar with the product, the
initial use should be done after the test. And then it can be
installed to the actual use.
2. What will come about if power supply is reverse?
It will immediately burn the drive.
3. What is the maximum of the upper control signal voltage ?
The maximum voltage of the speed regulation signal is 5V. Exceeding
this voltage will cause the drive to burn.
4. After the driver has been working for a long time, the shell is
hot. Is it normal?
Yes, it is. At room temperature, after long working hours, it is up
to 90 degrees. And it will not affect the performance.
5. The power indicator is light, but the motor does not turn and
shift, what is the reason?
There may be a mistake in the phase line and the Hall line. Please
re-energize the wiring according to the motor manual.
6. Can my motor speed transferred to 6000 with this drive?
The maximum speed of the brushless motor is determined by the
parameters of the motor itself. The drive can control the motor
speed from 0 to the highest speed.
7. I already have a motor and how to install this drive after
wiring?
You must first determine the motor phase and the definition of the
Hall line, and then you can connect it with wires. If you are not
sure, you need to ask the motor manufacturers. Incorrect wiring can
cause damage to the drive.
8. Can I add some features on this drive or do new product
development?
Yes, please contact us.
