AC80V-250V JKBLD1100 Brushless Dc Motor Driver for 110BLS motor
Bldc Controller
Product Overview:
JKBLD1100 is the latest high-tech product of our company, for the
field of medium power motor drive. It uses a large-scale integrated
circuit to replace the original hardware, so it has higher
performance of anti-jamming and fast response ability. It is
suitable for all the low voltage three-phase brushless DC motors
with peak current below 5A and low voltage AC80V-250V(boards show
AC80V-220V) ,whether the motor driver with Hall or not. It is
widely used in knitting equipment, medical equipment, food
packaging machinery, electric tools and a series of electrical
automation control area .
Main features:
It can be connected with an external speed display board JK110BLS,
showing the speed, set drive parameters;
It has double speed closed current design with low speed torque and smooth operation;
It has high speed output with the maximum speed of 10000rpm / min;
The speed control mode is an external PWM speed and external potentiometer speed;
It has have EN, DIR,X1 signal control side;
It can output FG signals (optoelectronic isolation, gate output);
It can output ALM signals for the user to detect (optoelectronic
isolation, gate output);
It has over-current, overvoltage, under voltage, fan control and
Hall Sensor phase error, motor stalling and other protection
functions;
Electrical Specification:
(1)Environmental Temperature:25℃
| Power supply | AC80V～220V direct current (Capacity according to motor power selection) |
| The maximum input current | Not greater than5A (according to motor and rated load) |
| The maximum power | The maximum is 1100W(over power motor is strictly prohibited) |
| Adaptable motor | Adaptable output power ≤750W motor |
| Insulation resistance | General temperature﹥500MΩ |
| Insulation strength | General temperature and pressure 0.5KV,1minitute |
(2)EnvironmentalParameter
| Cooling method | Natural air cooling & forced air cooling |
| Environment | Condition | Avoid dust, oil mist and corrosive gases |
| Temperature | 0℃～+50℃ |
| Humidity | ﹤80%RH,no condensation, no frost |
| Vibration | ﹤0.5G(4.9m/s2 )10Hz-60Hz (non-continuous operation) |
| Reserved temperature | -20℃～+65℃ |
| Size | 150mmX97.5mmX53mm |
| Weight | About 0.55Kg |
Note: Due to dramatic changes in the temperature of the storage
environment, it is easy to form condensation or frost. In this
case, the drive should be placed for 12 hours or more. Until the
drive temperature and ambient temperature is consistent, it can be
on power.
Terminal interface description:
| Function | Mark | Description |
| Indicator light | POWER | If the green power indicator is lighten, it shows that power is
normal. |
| ALM | If the red status indicator is slow flash, it means waiting; Quick
flash means operation; It always lights meaning faults or off-line; |
| RS232 communication port | TTL | It can be connected with an external speed display board JK-BL01 to
display speed. JK-BL01 can also set the drive parameters. Details
are shown in JK-BL01 instructions |
| Control signal port | +5V1 | Control signal power+( inner power output ) |
| VSP | External speed control signal Control way: (1)By connecting with a potentiometer to change VSP,
then it can complete 0 ~ 100% speed adjustment. The range is 0-5V; (2)speed control by PWM: positive terminals connect with VSP, and
negative terminals connect with GND1, inputting frequency by VSP to
change duty cycle, and speed changed, the range is 100-100KHz |
| X1 | Input signal, brake on low level or to GND1, the red light keep
off(Brake braking force can be adjusted by customer’s
requirement),When X1 is connected with +5V1 or without any port ,
motor keeps running. |
| FG | Motor speed pulse output is measuring the frequency of this signal.
Then converts it into the actual motor speed. |
| DIR | Rotary direction is controlled by high and low electrical level,
motor forward: connected with GND1, motor reversal (anticlockwise)
;without GND1 or connected with +5V, motor forward (clockwise) |
| EN | Connected EN with GND1, motor can work(online status);without
connected or connected with +5V1,motor can not work(offline status
and the red light keep working) |
| ALM | ALM signal output. When the power is in danger, the current flow is
slow. |
| GND1 | Control signal’s power supply |
| Hall control port | +5V2 | + motor’s Hall power |
| HU | Hall sensor signal U phase input |
| HV | Hall sensor signal V phase input |
| HW | Hall sensor signal W phase input |
| GND2 | The motor’s Hall power supply |
| The motor and power | U,V,W | The motor’s three-phase output signal |
| AC1,AC2 | The input power is AC80V～250V.(boards show AC80V-220V) |
General problems
1. How can get it started as soon as possible when you first use
the drive?
After you correctly connect the power cord, the motor line, the
Hall line, the external potentiometer slowly accelerates. After the
motor is turned correctly, you can test the enable, direction and
other functions. If you are unfamiliar with the product, the
initial use should be done after the test. And then it can be
installed to the actual use.
2. What will come about if power supply is reverse?
It will immediately burn the drive.
3. What is the maximum of the upper control signal voltage ?
The maximum voltage of the speed regulation signal is 5V. Exceeding
this voltage will cause the drive to burn.
4. After the driver has been working for a long time, the shell is
hot. Is it normal?
Yes, it is. At room temperature, after long working hours, it is up
to 90 degrees. And it will not affect the performance.
5. The power indicator is light, but the motor does not turn and
shift, what is the reason?
There may be a mistake in the phase line and the Hall line. Please
re-energize the wiring according to the motor manual.
6. Can my motor speed transferred to 6000 with this drive?
The maximum speed of the brushless motor is determined by the
parameters of the motor itself. The drive can control the motor
speed from 0 to the highest speed.
7. I already have a motor and how to install this drive after
wiring?
You must first determine the motor phase and the definition of the
Hall line, and then you can connect it with wires. If you are not
sure, you need to ask the motor manufacturers. Incorrect wiring can
cause damage to the drive.
8. Can I add some features on this drive or do new product
development?
Yes, please contact us.
