Hdep Geocell Cellular Confinement for Ground Stabilization Slope
Protection Ground Grid
About Hengquan
We have experience for more than 7 years. There are two product
lines for geogrid and geocell. Factory work 24hours a day, we sold
more than 100,000,000rmb last year(2020). Our customers are all
over the world.
Brief Introduction of Geocell Confinement System
Geocells are cellular confinement systems that were created as an
easy and durable material that are used for stabilizing and
protection. Cellular confinement systems effectively maintain the
soil’s compaction, and, by doing so, create a stronger structure
for both the infill and pavement. The cells’ three-dimensional,
honeycomb design ensures that the Geocell is strong and durable.
This format creates a structure that improves load distribution.
The cell is made from a high density polyethylene (HDPE), which is
used to stabilize weak or unsteady soil. That ability is a result
of their ability to reduce lateral movement of soil particles while
vertically loading on the contained infill.
Geocell Confinement System Characteristic
Geocell greatly reduces erosion caused by weather and heavy or
repeated traffic. Through the perforation mode of each unit and
weld, the water is allowed to drain freely without flushing the
material. Textured surfaces provide additional material retention.
It is very suitable for the construction of erodible slopes and
embankments, as well as driveways, roads, parking lots,
playgrounds, trails, etc.
Laying method
① Foundation treatment
Firstly, the lower layer shall be leveled and rolled. The flatness
shall not be greater than 15mm, and the compaction shall meet the
design requirements. Hard protrusions such as gravel and stones are
strictly prohibited on the surface.
② Laying geogrid
a. When storing and laying geogrids, avoid exposure and long-term
exposure to avoid deterioration of performance.
b. It shall be laid perpendicular to the line direction, overlapped
and firmly connected according to the requirements of the design
drawings. The strength of the joint in the stress direction shall
not be less than the design tensile strength of the material, and
its lamination length shall not be less than 20cm.
c. The quality of geogrid shall meet the requirements of design
drawings.
d. During construction, it is necessary to maintain continuity
without deformation, wrinkling and overlap. Pay attention to
tension the grid by hand to make it uniform and flat, close to the
lower bearing surface, and fix it with nails and other measures.
e. For the geogrid, the long hole direction is consistent with the
cross section direction of the line, and the geogrid shall be
straightened and leveled. The end of the grating shall be treated
according to the design.
f. After the geogrid is laid, the filler shall be filled in time at
an interval of no more than 48 hours to avoid direct exposure to
the sun.
③ Fill
After the grating is laid, it shall be filled in time. The filling
shall be carried out according to the symmetrical principle of "two
sides first and then the middle", and it is strictly prohibited to
fill the middle of the embankment. The filler shall not be unloaded
directly on the geogrid, but must be unloaded on the paved soil
surface, and the unloading height shall not exceed 1m. All vehicles
and construction machinery shall not walk directly on the paved
geogrid, but only along the embankment.
④ Rolling grating
After the first layer of filler reaches the predetermined thickness
and is rolled to the design density, roll the grid back for 2m,
bind it to the previous layer of geogrid, manually trim and anchor,
and plant 1m soil outside the rolling end to protect the grid from
human damage.
⑤ The laying of one layer of geogrid shall be completed according
to the above method, and the laying of other layers of geogrid
shall be carried out according to the same method and steps. After
the grid is laid, the upper embankment will be filled.
Factory and Equipment:
Product inventory:
Application:
Functioning by filling the pores with a three-dimensional honeycomb
structure, the geocell cellular confinement system offers
alternative solutions to geogrid material. Working with the logic
of geogrid, geocell undertakes the tasks of reinforcement of
geogrids on the ground and reinforcement on retaining walls.
Differently, cellular confinement systems work by filling the
cellular fillings.
Product Type | Height
(mm) | Welding Distance
(mm) | Thickness
(mm) | Tensile Strength of Welding Points (N/cm) | Tensile Strength of Connection of Cells(N/cm) | Tensile Strength at Yield of Each Sheet (Mpa) |
| 50≤H≤250 | 330≤A≤1000 | 1.0~1.2 | ≥100 | ≥120 | ≥20 |
| 50≤H≤250 | 330≤A≤1000 | 1.0~1.2 | ≥100 | ≥120 | ≥20 |
Textured and Not Perforated | 50≤H≤250 | 330≤A≤1000 | 1.5~1.7 | ≥100 | ≥120 | ≥20 |
| 50≤H≤250 | 330≤A≤1000 | 1.5~1.7 | ≥100 | ≥120 | ≥20 |
HDPE geocell type | | | Load quantity per 40'GP (Sqm) ( m2) |
Smooth Perforated and Not Perforated | | | about 16500 |
Smooth Perforated and Not Perforated | | | about 11100 |
Smooth Perforated and Not Perforated | | | about 20400 |
Smooth Perforated and Not Perforated | | | about 13600 |
Year of Registration: 2014
Place of Registration: China
Registrated Capital: CNY105,000,000.00
Briture Co., Ltd
was approved by Chinese Bureau of Commerce
Leo
Tel: +8615031817097
Whatsapp/Wechat: +8615031817097
Email: leo@hengquan-china.com
Website: www.plastic-geogrid.com
Download PDF: Catalog of Hengquan - geocell.pdf
