HXE-14DH Copper wire drawing machine with large spool
I. Application of machine
This machine adopts programmable controller and dual inverters, the
sliding and automatic speed control and variable speed. With energy
Low consumption, high reliability, small slip rate, long life,
large capacity of take-up, low noise, nice shape, etc.Machine is
operation simply, safe, reliable, and easy maintenance. In order to
make the user familiar with and master the rules, please users read
this manual carefully before using.
II. Parameters
(1) Inlet : ф1.6mm/max copper; ф2.5mm/max aluminum
(2) Outlet: ф0.25-ф0.65mm; ф0.4-ф0.8mm
(3) Mechanical speed: 800MPM/MAX
(4) Dies: 14 (buyer-owned) Max
Dies: 7 (buyer-owned) Minimum
(5) Dies OD: ф25mm X 8 - 12mm thick
(6) Slip ratio: 1 -13, 15%;14, 8%
(7) Main motor: AC15.5KW motor
(8) Take-up motor: AC7.5KW motor
(9) Take-up diameter: ф400 - ф500
(10) brake: pneumatic brakes
(11) Power consumption:15-30kw power
(12) Lubrication capacity: 150L/MIN
III. Components
| Name | Quantity |
| 1. Pay-off stands | 1 set |
| 2. HXE-14DS Drawing machine | 1 set |
| 3. Spare parts |
IV. Note
1. to achieve the requirements of this specification, the cable
must be reasonable, good Lubricating fluid, good Dies, and
high-quality copper wire.
2. not used the reel without balancing requirement.
Electrical system normal conditions are as follows:
A. Environmental temperature: -10 ℃ ∽ +40 ℃ (no freezing
conditions), a 24-hour period, the average temperature does not
exceed +35 ℃.
B. atmospheric conditions: air, harmless dust, corrosive and
explosive gases.
C. Relative humidity: +40 ℃ when the maximum temperature does not
exceed 50%, a lower temperature allows a higher relative humidity
of 85% at +20 ℃.
D. Altitude: not more than 1000M, more than 1000M, specified in
accordance with this.
Elevation
m | Correction facto |
| Current | Withstand |
| 1000 | 1 | 1 |
| 1500 | 0.99 | 0.95 |
| 3000 | 0.96 | 0.80 |
| 6000 | 0.90 | 0.56 |
E. Power supply voltage: sinusoidal, three-phase four-wire 380V,
50HZ; voltage fluctuation range does not exceed the rating of ± 5%,
should ensure that output ratings; voltage fluctuations not
exceeding ± 10%, should ensure reliable operation ; frequency
fluctuations should not exceed the rating of ± 2%.
F. Install inclination: Vertical mounting installation inclination
should not exceed 5%.
V. Attention
5-1. If wire breaks, will stop automatically, and the Fault
Indicator light will open.
After connect the wire, press the Fault Reset button(Yellow button)
and the On button (Green button), to run the machine again.
5-2. Press Emergency Stop button(Red button) to shut down the
machine immediately.
After solve, press the button again to run the machine.
5-3. After set the Length-counter, the machine will stop
automatically when reach the length set.
After change the Spool, please press the Length Reset button(Yellow
button) and the Spool Reset button(Yellow button) to run the
machine again.
5-4. After the machine stop(no running at all), then switch the
Pump switch to stop the lubrication.
5-5. Do not touch the wire in the Annealing section.
5-6. After shut down the machine, need at least 30 seconds to
restart the machine.
5-7. Wire often breaks, adjust the speed, balance arm, check the
dies are clean or not.
5-8. If has scratch on the surface of the wire, check the capstans
on the Take-up part. Check the drawing capstans.
VI. Working Environment
6-1. Not more than 1000 meters above sea level.
6-2. Temperature －10℃－40℃
6-3. Relative temperature does not exceed 85% (25 ℃)
