100mbar 19mm Compact Conventional Pressure Sensor Core
HT19 Silicon Piezoresistive Pressure SensorIntroduction:HT19 is a silicon piezoresistive pressure sensor featuring a highly
stable diffused silicon sensing element. It accurately measures the
pressure of liquids and gases by transmitting medium pressure to
the silicon diaphragm through an isolation diaphragm and silicone
oil. With its compact size, high accuracy, and cost-effectiveness,
this versatile sensor is widely used in applications such as air
compressors and refrigeration systems.
1.Utilizing advanced technology and 316L stainless steel housing,
along with materials such as titanium and Hastelloy for the diaphragm
2.Employing thick-film circuits for temperature compensation and
zero-point correction
3.outstanding reliability, repeatability, and stability
Applications:
1.Suitable for measuring non-corrosive gas and liquid pressure with
316L stainless steel compatibility
2.Applied in various industrial process sites, including petroleum,
chemical, metallurgy, power, and hydrology
3.Used in marine and aviation industries
4.Suitable for hydraulic and pneumatic control systems
5.Utilized in process control applications
Electrical performance:1.Power Supply: ≤2mA DC (Typical 1.5mA DC)2.Input Impedance:3KΩ~6KΩ3.Output Impedance:2.5KΩ~6KΩ4.Electrical Connection:Gold-plated Kovar pins or 100mm
high-temperature wires.| Performance Parameters: |
| Range | Gauge(G) | 10KPa,20KPa,35KPa,100KPa,200KPa,350KPa,1000KPa,2000Kpa |
| Absolute(A) | 100KPaA,200KPaA,350KPaA,700KPaA,1000KPaA,2000KPaA |
| Sealed(S) | 3500KPaS,7MPaS,10MPaS,20MPaS |
| Typ | Max | Unit |
| Nonlinearity | ±0.15 | ±0.3 | %F.S |
| Repeatability | 0.05 | 0.1 | %F.S |
| Hysteresis | 0.05 | 0.1 | %F.S |
| Zero Output | 0±1 | 0±2 | mV |
| Span Output | ≤20KPa | 50±10 | 50±30 | mV |
| ≥35kPa | 100±10 | 100±30 | mV |
| Temperature Error-Zero | ≤20KPa | ±1 | ±2 | %F.S |
| ≥35kPa | ±0.5 | ±1 | %F.S |
| Temperature Error-Span | ≤20KPa | ±1 | ±2 | %F.S |
| ≥35kPa | ±0.5 | ±1 | %F.S |
| Compensated Temp. | ≤20KPa | 0~50 | ºC |
| ≥35kPa | 0~70 | ºC |
| Operating Temperature | -20~80 | ºC |
| Storage Temperature | -40~125 | ºC |
| Allowable Overload | Take the smaller value between 3 times the full scale or 120MPa | |
| Burst Pressure | 5X the full scale | |
| Long-term Stability | 0.2 % | F.S/Year |
| Diaphragm Material | 316L | |
| Insulation Resistance | ≥200MΩ 100VDC | |
| Vibration | No change under conditions of 10gRMS, 20Hz to 2000Hz | |
| Shock | 100g,11ms | |
| Response Time | ≤1ms | |
| O-ring Seal | Nitrile ring or Fluoro ring | |
| Filling Medium | Silicon Oil | |
| Weight | about 20g | |
| The parameters are tested under the following conditions: 1.5mA @
25°C |
| Outline Construction |
| type1 |  |
| type2 |  |
| Electrical connection and compensation |
|
1. Core-to-Housing Fit: Ensure the core size is compatible with the transmitter housing
prior to assembly to achieve the required level of airtightness.
2. Housing Assembly: During assembly, maintain vertical alignment of the housing and
apply even, controlled pressure to prevent jamming or damage to the
compensation plate.
3. Media Compatibility: Verify that the measured medium is chemically compatible with the
core diaphragm and housing material (316L stainless steel). If
compatibility is not guaranteed, you must provide special
instructions at the time of order placement.
4. Diaphragm Protection: Never touch the sensor diaphragm with fingers or sharp objects.
The diaphragm is extremely sensitive and can be permanently damaged
by deformation or piercing.
5. Gauge Pressure Reference: For gauge pressure cores, the pressure port must remain open to
atmospheric pressure. Take care to prevent moisture, water vapor,
or any corrosive media from entering the negative pressure chamber.
6. Electrical Connections: Always refer to the wiring label attached to the actual core for
pin lead connections. Do not rely on external documentation if the
pin configuration has been modified.
1.Q: What are the features of your pressure sensor transmitters?
A: High precision, durability, and excellent performance.
Customization available.2.Q: Can I customize special specifications?
A: Yes, our engineers can tailor products to meet specific needs. We provide OEM and ODM service3.Q: What is your production capacity?
A: Our manufacturing facilities can produce up to 30,000 pressure
sensor transmitters per month, so we are fully capable of meeting
the needs of large-scale orders. However, it is advisable to
contact our sales team in advance to ensure smooth production and
delivery scheduling
.4.Q: What's the typical delivery period?
A: 5~8 working day for standard models. Customized products may vary.5.Q: How are the products priced? Any discounts?
A: Competitive pricing with discounts for bulk orders or long-term
partners
.6.Q: What is the warranty of your products? And after-sales
service?
A: Our warranty time is 24 months after shipment, and our
after-sales will respond with your questions in 24hrs, remote
instruction by PC network is always available.
