Mesh Radio Link Wireless Data Transmitter For Drone Long Range
Communication
Key Features:
- Wireless link rate is up to 735kbps.
- It supports point to point, point to multipoint, multipoint to
point and Mesh network topologies.
- It supports Mesh networking with up to 1024 nodes.
- High sensitivity level of -114dBm at 125kHz.
- Supports frequency hopping spread spectrum (FHSS).
- Drone data link Air-to-ground LOS(light of sight) range more than
300km.
Overview:
HNC1 self-organizing Mesh radio wireless data transmitter enables
centerless long range real time communication between large-scale
nodes, all nodes can communicate with each other independently
without interfering, supports large-scale dense node access to
wireless transmission, dynamic networking and flexible
reorganization, supports full-multiplexing communication, the node
sends data at the same time it can also receive the data of all
other nodes without interfering with each other, and in the absence
of the center, it can realize the interoperability of any node and
all other nodes in the network. Without interfering with each
other, it can realize the interconnection between any node in the
network and all other nodes in the case of no center.
HNC1 data link mesh radio supports large-scale node access,
multi-hop self-organizing network, 20W transmit power, -114dBm
sensitivity, maximum 735kbps effective data transmission rate, 2ms
ultra-low latency, which can be used for swarming drones, Internet
of Things, data chain, remote control, data collection, artificial
intelligence, military equipment and other application scenarios.
HNC1 20W data link mesh radio models:
| Model | RF Power | Network Scale | Frequency Bands |
| HNC1-H800-20W | 20W | Max. 1024 nodes, up to 16 hops | 820~854MHz |
| HNC1-H900-20W | 900~940MHz |
|
| HNC1-F800-20W | 20W | Max. 256 nodes, up to 3 hops | 820~854MHz |
| HNC1-F900-20W | 900~940MHz |
Technical Specifications:
| Frequency | Different models support different frequency bands, see above
models table |
| Bandwidths | 1MHz/500kHz/250kHz/125kHz selectable |
| Frequency hopping speed: | - 1MHz:Over 1800 times per second
- 500kHz:Over 900 times per second
- 250kHz:Over 450 times per second
- 125kHz:Over 225 times per second
|
| Effective data rate | - 1MHz: Up to 735kbps
- 500kHz:Up to 370kbps
- 250kHz: Up to 185kbps
- 125kHz: Up to 92kbps
|
| Full-multiplexing communication | Support |
| Air-to-ground LOS(light of sight) distance | ≥300km |
| Centerless self-organized network | Support centerless self-organized network, any node of the network
is destroyed without affecting the communication; |
| Network construction time | Within 1 second |
| Wireless transmission delay | Minimum 2ms |
| Dynamic topology | Support dynamic topology, support node joining and leaving, network
topology change and deformation can be normal communication; |
| RF power | 20W(43dBm) |
| Sensitivity | - 125kHz:-114dBm
- 250kHz: -111dBm
- 500kHz:-108dBm
- 1MHz:-105dBm
|
| Frequency stability | ≤1ppm |
| Modulation | QPSK modulation LDPC coding |
| Encryption | 128-bit encryption |
| Low power consumption((varies by data rate) | Less than 1.5W(0.06A/24V) when receiving, transmission power
consumption (B is in bytes): - 1.2KB/s: 2.4W(0.1A@24V)
- 3.4KB/s: 3.9W(0.16A@24V);
- 6.4KB/s: 5.5W(0.23A@24V);
- 12KB/s: 9.6W(0.4A@24V);
- 26KB/s: 19.2W(0.8A@24V);
- 37KB/s: 24W(1A@24V);
- 48KB/s: 32W(1.35A@24V).
|
| Operating voltage | 24V as default, supports a wide voltage input of 7-36V.
Transmission power varies with voltage: - 7V:2W
- 12V:5W
- 18V:10W
- 24V:20W
- 20-36V:20W-30W
- Power supply capacity requirement: ≥2.5A @ 24V (20W)
|
| Operating temperature | -40～+55°C |
| Dimensions | 82.5*52*16mm |
| Weight | 90.7g |
| Input /Output | Description |
| J30JZ-9PIN connector | Power-input, uart, M0 control signals |
| M1 Dipswitch | M1 control signal |
| SMA female | Antenna port, the required antenna impedance is 50Ω |
J30JZ-9PIN connector
J30JZ-9PIN connector PIN signal can be assembled as TTL3.3Vor RS232
uart port or RS422 uart port
