| Base parameters | |
| Measuring medium | Liquid or gas (compatible with contact material) range< 10 kPa
(non-conductor, non-corrosive, non-explosive gas with humidity
≤90%RH, no condensation) |
| Measuring range | -100kPa~0~100MPa (see range selection table for details) |
| Pressure mode | Gauge pressure, absolute pressure, negative pressure |
| Media temperature | -40～150℃ |
| On-time | 20ms |
| Stable performance | ± 0.1% FS/year |
| Temperature drift | ±0.01%FS/°C (temperature compensation range) ±0.05%FS/°C (outside
temperature compensation range) |
| Degree of protection | IP65 (no display) IP54 (with display) Note: The above protection
level refers to the electrical connection is complete |
| Durable performance | 10X10⁶ times (lower range to upper range cycles) |
| Overall weight | No display≈ 320g Yes≈360g |
| resolution | Analog output 0.01%FS, digital output 0.05%FS |
| Output power supply: | |
| Output signal | 4~20mA,RS485,0~10VDC,0~5VDC,1~5VDC,0.5~2.5VDC |
| Power supply range | 9～36VDC,15～36VDC,3～5VDC |
| Accuracy class | 0.1%FS,0.25%FS,0.5%FS |
| Response frequency | 5Hz,30Hz,100Hz |
| Maximum power: | |
| Current type | ≤0.02Us(W) |
| Voltage type | ≤0.02Us(W),≤0.008Us(W) ,≤0.001Us(W) |
| Digital | ≤0.02Us(W),≤0.015Us(W) |
| Load characteristics: | |
| Voltage type | ≥10kΩ |
| Current type | No display load ≤ {(Us-7.5)÷0.02}Ω (Us=Supply voltage) Display load
≤{(Us-12)÷0.02}Ω (US=Supply voltage) |
| Environmental conditions: | |
| Ambient temperature | -40～85℃ |
| Ambient humidity | 0%~95%RH(no condensation, no condensation) |
| Overpressure and blasting | 600%FS,500%FS,400%FS,300%FS,20kPa,200kPa,600kPa,900kPa,1.25MPa,2MPa,3MPa,5MPa,9MPa,12.5MPa |
| Overall material: | |
| diaphragm | 316L stainless steel (contact with the medium to be measured) |
| Process connection | 304 stainless steel (contact with the medium to be measured) |
| enclosure | 304 stainless steel |
| Seals | Seen pressure and blasting charts (contact with the medium being
measured) |
| Hirschmann joints | ABS engineering plastics, |
| Display the shell | ABS Engineering Plastics (LED Display) |
| Hirschmann joints | ABS engineering plastics |
| Mechanical stability: | |
| Seismic performance | 10g(20… 2000Hz) conforms to IEC60068-2-6 standard |
| Impact resistance | 500g/ms conforms to IEC60068-2-27 standard |
| Electrical protection: | |
| Short-circuit protection | perpetual |
| Anti-polarity protection | No damage, but not working |
| Insulation resistance | ≥100MΩ 500VDC |
| Dielectric strength | 500VAC |
| Output Limits: |
| The output is minimal | 4mA,3.8mA,0,0.001VDC,0.05VDC |
| Output maximum | 20mA,26mA,2000,12VDC,10VDC,5VDC |
