Grundfos Crie Vertical Multi-Stage Centrifugal Pump with Integrated Frequency Converter Suitable for Heating and Irrigation

Meet Your Water Needs with CRI E Pumps
The CRI E pump is an in - line multistage pump with a built - in variable speed drive, suitable for various flow rates and pressures. Made of AISI 304 stainless steel, it is suitable for non - corrosive liquids. The built - in or external frequency converter of CRI E, along with the optional IE5 motor, makes it highly suitable for applications that require top - notch performance and control, as well as industry - leading energy efficiency. Use CRI E for liquid transportation, circulation, and boosting of cold or hot water.

MGE Motor Enhances Efficiency and Control An IE5 MGE motor is available. It has the highest energy efficiency in the market and can adapt to continuously changing pump speeds, giving you full control. Highest Standards All parts in contact with the medium are made of AISI 304 stainless steel, suitable for various corrosive water environments, ensuring no corrosion. Appropriate Solutions The maximum - flow CRI E pump is the CRI E 20, with a flow rate of up to 29.6 m³/h and a pressure of up to 25 bar. Multifunctional Solutions The special water pump for deep - well pumping is suitable for small - scale water supply systems, with a maximum pumping depth of up to 90 meters.

CRI E 20 - 6 V - FGJ - A - E - HQQE

• "Power - on": The motor is running (rotating green indicator light) or not running (steady - on green indicator light).
• "Warning": The motor is still running (rotating yellow indicator light) or has stopped (steady - on yellow indicator light).
• "Alarm": The motor has stopped (flashing red indicator light).
  Communication with the pump can be carried out through Grundfos GO Remote (accessory). The remote control can be used for further settings and reading of certain parameters, such as "actual value", "speed", "input power" and "total power consumption". The terminal box has a large number of input and output interfaces, enabling the motor to be used in advanced applications that require more inputs and outputs.
• Two dedicated digital inputs
• Three analog inputs: 0(4) - 20 mA, 0 - 5 V, 0 - 10 V, 0.5 - 3.5 V
• 5V power supply for potentiometers and sensors
• One analog output: 0 - 10 V, 0(4) - 20 mA
• Two configurable digital inputs or open - collector outputs
• Two Pt100/Pt1000 inputs
• LiqTec, dry - running protection sensor input
• Grundfos digital sensor input and output
• 24V supply voltage for sensors
• Two signal relay outputs (potential - free contacts)
• GENIbus connection
• Grundfos CIM bus module interface

Liquid

• Transported liquid: Water
• Liquid temperature range: -20..120 °C
• Liquid temperature during operation: 60 °C
• Density: 983.2 kg/m³

Technology

• Pump speed on which pump data is based: 3529 revolutions per minute
• Rated flow rate: 25.3 m³/h
• Rated head: 101.9 meters
• Pump orientation: Vertical
• Shaft seal configuration: Single
• Main shaft seal: HQQE
• Shaft seal code: HQQE
• Approvals: CE, EAC, UKCA, SEPRO
• Approvals for drinking water: WRAS, ACS
• Curve tolerance: ISO9906:2012 3B

Materials

• Base: Stainless steel
  • EN 1.4408
  • AISI 316
• Impeller: Stainless steel
  • EN 1.4301
  • AISI 304
• Bearing: SIC

Installation

• Maximum ambient temperature: 50 °C
• Maximum operating pressure: 16 bar
• Maximum pressure at specified temperature: 16 bar / 120 °C; 16 bar / -20 °C
• Interface type: DIN / ANSI / JIS
• Inlet size: DN 50
• Suction port size: 2 inch
• Outlet size: DN 50; 2 inch
• Pressure rating for pipe connection: PN 25
• Flange rating inlet: 300 lb
• Flange size for motor: FF300

Electrical Data

• Motor standard: IEC
• Motor model: 160MH
• Rated power-P2: 11 kW
• Power required by the pump (P2): 11 kW
• Over/undersize motor: Standard motor size
• Power supply frequency: 50 Hz
• Rated voltage: 3 x 380 - 500 V
• Safety factor: 0.00
• Rated current: 20.3 - 16.0 A
• Cos phi-Power factor: 0.93 - 0.90
• Rated speed: 360 - 4000 revolutions per minute
• IE efficiency class: IE5
• Motor full - load efficiency: 93.1 %
• Encapsulation class (IEC 34 - 5): IP55
• Insulation class (IEC 85): F
• Motor number: 98971071

Controller

• Frequency converter: Built - in
• Pressure sensor: N

Others

• Terminal box position: 6
• Minimum efficiency index, MEI ≥: 0.70
• Net weight: 113 kg
• Gross weight: 145 kg
• Transport volume: 0.619 m³
• Custom tariff no.: 84137099.90

. Located in Tianjin, China, Tianjin Shiny-Metals Technologyco., Ltd. is a professional company that specializes in the research and development, design, production, sales, trade, and service of pumps. Our products are exported to more than 40 countries and regions, continuously building our global brand reputation. We offer a wide range of pumps, including centrifugal pumps, axial flow pumps, jet pumps, submersible pumps, deep-well submersible pumps, and swimming pool pumps, with over 500 specifications available. Our company has obtained the ISO 9001 certification from the International Organization for Standardization (CQC). In addition, our civilian motors have undergone product evaluation for CCC China mandatory certification. We have also received certifications such as CE, EMC, GS, RoHS, EAC, SASO, and ST. Our company is dedicated to meeting customer needs with high-quality products, reasonable prices, and exceptional pre-sales, in-sales, and after-sales services. We adhere to the management principles of "quality first, customer first, and reputation-based" and are committed to providing global customers with the best solutions for water pumps and water treatment systems, improving their quality of life. Our goal is to make the world a better place through water, and we strive to make water even better.