| Sign In | Join Free | My burrillandco.com |
|
...11 standards. Equipment Overview 1. Main purpose: This device is composed of two kinds of impact test apparatuses, and two kinds of mechanical strength test methods can be used to perform impact test on EVSE...
...Test Chamber Featuring Water Cooling Xenon Arc Technology for Accelerated Weathering and Material Aging Simulations Complied Standards & Clauses This water-cooling xenon weathering test chamber conforms to m...
... Impact Test Method for Metal Material,and adopts compressor cooling technology. Compressor refrigeration low temperature environmental chamber uti- lizes the heat balance principle and cycle stirring method...
... Dryer (whirlpool) It is a shrinkage tester appointed by American AATCC Meets to AATCC standard testing method (88B+C, 124, 130, 135, 142, 143, 150, 172 and 179) Drying methods: drying time for pre-school / ...
...exposed surface of the wall and ceiling. The test method is through the gradual change of the radiation heat, with small flame to ignite samples, and determination of the critical heat flux. BS476-7 Standard...
...”, JTG E20-2011 Standard Test Methods for Bitumen and Bituminous Mixtures for Highway Engineering of T 0736-2011 the “asphalt mixture spinning compacted specimen method (SGC)” requirements, and the associati...
... and manufactured according to ASTM D5800 Standard test method for evaporation loss of lubricating oils by the Noack B method. The noack evaporation loss Analyzer is suitable to determine lubricating oil(esp...
...standards GB/T 261-2008 Determination of Flash Point - Pensky-Martens closed cup method and ASTM D93 Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester. It is used to make determinatio...
...Determination of Ignition Temperature of Plastic Hot Air Furnace Method" and GB/T9343-2008 "Test Method for Combustion Performance of Plastics - Determination of Flash Ignition Temperature and Spon...
... a method for evaluating the odor of commercial LPG. Test method:A liquefied gas sample that has been completely vaporized is diluted with purified air to achieve a concentration of the target gas in the mix...
...Petroleum Products by Pensky-Martens Closed Cup Method". ASTM D93 Closed Cup Flash Point Tester is suitable to determine closed cup flash point of petroleum ......
... Standard Test Method for Flash and Fire Points by Cleveland Open Cup Tester. It is applicable to all petroleum products with flash points above 79ºC and below 400ºC. Product ......
..., and handballs. STANDARD SPECIFICATION Item Description Test method Three coordinate axes intersect in space Permissible error per point 0.02mm Control method PLC+HMI Probe repeatability 0.02mm Indication a...
... Method" and GB/T9343-2008 "Test Methods for Burning Properties of Plastics - Determination of Flash Ignition Temperature and Autoignition Temperature". It fully complies with the requirements...
Jetting resistance of drain and sewer pipes - Moving jet test method CEN/TR 14920:2005 Figure 1 Ceramic Nozzle CEN/TR 14920:2005 Pressure: 12±0.2 Mpa Flow 46±0.5L/min Gauge 10[-2,0]mm Angle 30±1° Speed 1m±0.1m/...
... rise characteristics requirements and testing methods for neutral electrodes (NE) in high-frequency surgical equipment. It can fully meet the testing requirements of standard 201.15.101.5 "Thermal performan...
... GB/T380 Standard Test Method for Sulfur Content in Petroleum Products (Lamp Method). It is used to determine the sulfur content in light oils(such as gasoline, kerosene) which the Reid vapor pressure is not...
...Test Furnace First, the scope of use The test furnace is developed according to the technical specifications and requirements specified in the national standard GB/T5464-2010, and is applicable to the test m...
...Testing Machine Product Description Equipment Overview The hydrostatic tester is suitable for long-term hydrostatic test of various plastic pipes, instantaneous hydraulic burst test of pipe and long-term con...
Surge Testing Machine, Surge Impulse Test / Short Circuit Test 1. Test object: stator and winding 2. Test method: connect the stator leads to the tester with clamps 3. Technical parameter Test object Stator, wi...