| Sign In | Join Free | My burrillandco.com |
|
... circuit; ► Provide 1-4 independent serial ports (RS232/422/485 optional) channel, physical isolation from each other, there is no correspondence between the ► RS232 / 485/422 interface, optional three data,...
... to a telephone line. Available in two 16-pin small outline packages, it eliminates the need for an analog front end (AFE), an isolation transformer, relays, opto-isolators, and a 2- to 4-wire hybrid. The Si...
... CPU monitoring each other, which improves products’safety performance ●DC20 ~ 28V wide voltage adaptability ●26 circuits of low voltage opto-coupling isolated input, 4 circuits of high voltagae opto...
... current limited contact wetting voltage if the contact is open. If the contact closes, current is drawn from the +10V supply which turns on the associated opto-isolator;...
...RS232 Integrated Controllers Coolmay Programmable Logic Controllers (PLCs) mainly include three series: CX3G, FX3GC, L02 series. CX3G-16M is the smallest PLC among all of the products. It applies military-gr...
..., 400*300mm 107682 STEP DRIVE PCB (GRADE FR4 LAMINATE 112389 SCB 40 PCB 107686 SCB9 OPTO ISOLATOR I/P PCB 107689 40 CHANNEL DIGITAL I/O PCB 117933 117933 I.C. ,...
HCPL-0302 Logic Output Optocouplers 8MBd 1Ch 0.5mA IGBT Gate Driver Optocouplers Description The HCPL-2300/HCPL-0300 optocoupler combines an 820 nm AlGaAs photon emitting diode with an integrated high gain phot...
MOC3021S-TA1 Lite-On Optical Coupler Circuit Board Chip 1 Channel FEATURES: * Isolation voltage between input and output Viso : 5,000Vrms * 6pin DIP photocoupler, triac driver output * High repetitive peak off-...
MOC3063S-TA1 Circuit Board Chip Lite-On Optical Coupler 1 Channel FEATURES: * Isolation voltage between input and output Viso : 5,000Vrms * 6pin DIP photocoupler, triac driver output * High repetitive peak off-...
... output capabilities. Equipped with 16 discrete outputs, it effectively handles a range of control tasks in industrial environments. Each channel features opto-isolation, which enhances protection against el...
...Power Protection Isolated Power Power Down Allowed <5ms Operating Temperature -20~70℃ Power Protection Isolated Power PORT1/PORT2 Pin1 Rx-(B) (PORT2 RS485) Pin2 RxD (PORT1 RS232) Pin3 TxD (PORT1 RS232) Pin4 NA Pin5 GND Pin6 Rx+(A) (PORT2 RS485) Pin7 NA ......
... control, 2-phase sinusoidal output current drive l Supply voltage from 18VDC to 50VDC l Opto-isolated signal I/O l Overvoltage, under voltage, overcurrent, phase short circuit protection l 15 channels subdi...
... control, 2-phase sinusoidal output current drive l Supply voltage from 18VDC to 50VDC l Opto-isolated signal I/O l Overvoltage, under voltage, overcurrent, phase short circuit protection l 15 channels subdi...
... Description Of UCC23313BQDWYRQ1 The UCC23313BQDWYRQ1 is an Opto-compatible, singlechannel, isolated gate driver for IGBTs, MOSFETs and SiC MOSFETs, with 4.5-A source and 5.3-A sink peak output current and 3...
...application. This device operates as an isolation amplifier for these modules and provides the required electrical isolation between the input and output with an opto-coupler.Recommended IGBT modules: VcES =...
... White Paint Option Filter: Type-C, RS232, DC, USB2.0, USB3.0, RJ45, AC, HDMI, VGA, PS2, BNC, SMA, DB25 Option Fans & Heatsink Support: 5G(millimeter wave ),WIFI,WIFI6,BLE,UWB,433MHz,GPS Isolation: > 80dB at...
... White Paint Option Filter: Type-C, RS232, DC, USB2.0, USB3.0, RJ45, AC, HDMI, VGA, PS2, BNC, SMA, DB25 Option Fans & Heatsink Support: 5G(millimeter wave ),WIFI,WIFI6,BLE,UWB,433MHz,GPS Isolation: > 80dB at...
... frequency amounts to 200Kpps Once the pulse stops over 100ms, the phase current will automatically cut by half Bipolar constant current chopper control Opto-isolated signal Input/Output Driving current is c...
... response frequency amounts to 200Kpps Once the pulse stops over 1.5s, the phase current will be automatically reduced to half of pre-set current Opto-isolated signal Input/Output Driving current can be adju...
... response frequency amounts to 200Kpps Once the pulse stops over 1.5s, the phase current will be automatically reduced to half of pre-set current Opto-isolated signal Input/Output Driving current can be adju...