SS304 Material Long Distance Hanging Bearing U Model Screw
Conveyors
I. Overview.
This screw conveyor is composed of planetary cycloid pin gear
reducer, coupling, (or sprocket, chain) screw shaft, intermediate
hanger, bearing seat, trough and bracket. The screw shaft is driven
to rotate by the reducer and coupling, so that the material
entering the trough does not rotate with the spiral due to its own
gravity and the friction force on the trough, and only moves along
the trough to achieve the purpose of conveying materials.
II. Working principle and Applictaion
The screw conveyor uses the rotating screw to move the conveyed
material along the fixed casing to carry out the conveying work.
The head and tail bearings are moved to the outside of the casing.
The hanging bearing adopts a sliding bearing and is equipped with a
dust-proof sealing device. The bearing bush is generally used
Powder metallurgy, the conveying cement adopts felt bearing bushes,
and the suspension shaft and the screw shaft are connected by
sliding blocks
Screw conveyors are suitable for various industries, such as
building materials, chemical industry, electric power, metallurgy,
coal, food and other industries, and are suitable for horizontal or
inclined conveying powder, granular and small lump materials, such
as coal, ash, slag, cement, grain, etc. , The material temperature
is less than 200℃. The screw machine is not suitable for conveying
materials that are perishable, viscous, and easily agglomerated.
III.Characteristics are below
1. Large carrying capacity, safety and reliability.
2. Strong adaptability, convenient installation and maintenance,
and long life.
3. The whole machine is small in size and high in speed, ensuring
fast and uniform delivery.
4. The discharge end is equipped with a cleaning device, the whole
machine has low noise, strong adaptability, and flexible layout of
the inlet and outlet positions.
5. Good airtightness, the shell is made of seamless steel pipes,
and the ends are connected by flanges to form a whole, with good
rigidity.
IV. Technical parameter
| Model | Diameter mm | Pitch mm | Speed r/min | Standard Capacity(m3/h) | Speed r/min | Standard Capacity(m3/h) | Speed r/min | Standard Capacity(m3/h) |
| φ0.45 | φ0.33 | φ0.15 | φ0.45 | φ0.33 | φ0.15 | φ0.45 | φ0.33 | φ0.15 |
| LS20 | 200 | 200 | 100 | 16.9 | 12.4 | 5.6 | 80 | 13.5 | 9.9 | 4.5 | 63 | 10.7 | 7.8 | 3.6 |
| LS315 | 315 | 315 | 80 | 52.9 | 38.8 | 17.6 | 63 | 41.6 | 30.5 | 13.9 | 50 | 33.1 | 24.2 | 11 |
| LS400 | 400 | 355 | 71 | 85.3 | 62.5 | 28.4 | 56 | 67.3 | 49.3 | 22.4 | 45 | 54.1 | 39.6 | 18 |
| LS500 | 500 | 400 | 63 | 133.2 | 97.7 | 44.4 | 50 | 105.8 | 77.6 | 35.3 | 40 | 84.6 | 62.0 | 28.2 |
Ⅴ.Selection Conditions of Trough Auger Conveyor
| Material to be processed: _____ | Working environment is indoor or outdoor:________ |
| Handling capacity: ________per hour | Working environment temperature: _______ ℃ |
| Bulk Density: _____t/m3 | Installation form is horizontal or inclined : ________ |
| Conveying distance: ________ | If it is inclined,what is the inclined degree_____° |
| Material size:____mm | Water content:____% |
| Material temperature: _______ ℃ | Working power supply: _____V ______HZ ______PH |
VI.Equipment installation requirements
a. The on-site installation of the inlet and outlet should make the
flange support surface of the inlet and outlet parallel to the axis
of the screw machine; the flanges connected to it should be tightly
fitted and there should be no gaps.
b. After the screw machine is installed, check whether there is
enough lubricating oil in each oil storage place, if not enough,
add enough, and then carry out a no-load test run; check the screw
machine after running for more than 4 consecutive hours. Accuracy
of assembly: Stop immediately when an abnormality is found, and
operate after treatment until it is in a good operating state.
c. The operation of the screw machine should be stable and
reliable, and the fasteners should not be loosened. The reducer has
no oil leakage, no abnormal sound, electrical equipment is safe and
reliable, and the no-load operating power is less than 30% of the
rated power.
