HXE-24DT Small copper wire drawing machine with annealer
I. Quick description
HXE-24DT Small copper wire drawing machine with annealer is used to
draw and anneal single bare copper wire from 0.5mm-1.0mm to
0.07mm-0.25mm.
II. Main Technical parameters
1. Usage single bare copper wire drawing and annealing
2. Inlet size 0.5mm-1.0mm
3. Outlet size 0.07mm-0.25mm (Elongation of annealed wire 25% to
32%)
4. Machine speed/max 1800m/min
5. Die number 24, Dies size 25mm×8-10mmT, Slip ratio 13%+8%
6. Wire drawing mode standing-mode and 4axes
7. Drive by Inverter control, Brand Inovance, Most widely used
brand in drawing machine
8. Main motor 15KW, Spooler motor 3.7KW, China best brand
9. Annealing voltage DC50V/max, Annealing current DC300A/max,
Annealing power 15KVA
10. Annealing method DC Three section annealing
11. Annealing protection will be done by steam protection
12. Capacity of compressed air 0.4-0.6Mpa, 20L/min
13. Demand Water quantity for annealing and coolant 200L/min
14. Machine frame welded by steel plate
15. Transmission Flat belts
16. Capstan Ceramic plasma
17. Lubricating system Pipe Spray
18. Bobbin size 300mm, loading capacity: 50kg/max
19. Bobbin loading & unloading type shaft type
20. Traversing unit 110W synchros motor, width: 270mm/max
21. Tension control by Air pressure tension control (With Weight
balance as Backup)
22. Cabinet 0.8m*0.6m*2.0m
23. Machine dimension 2.3m*1.6m*1.9m; Installation Area
3.3m*1.7m+0.8*0.6m
24. Machine weight 3400KG, Cabinet weight 500KG. In total for
shipping around 4,000KG.
III. Components
| Name | Quantity |
| 1. Pay-off shelf | 1 set |
| 2. HXE-24DT Drawing&Annealing machine | 1 set |
| 3. Electrical control system | 1 set |
| 4. Steam generator | 1 set |
| 5. Lubrication Tank and Pump | Optional |
| 6. Spare parts | As per List |
| 7. Operation Manual, Inverter Manual |
IV. The structure and principle of the machine
4-1. The annealing part, is three-section annealing, consist of
Preheating section, annealing section and drying section. The fix
speed capstan of drawing, the annealing capstans, are driven by the
same motor, through belts, so the speed of drawing, speed of
annealing, is the same, make sure no wire break.
4-2. The annealing capstans, are access to positive and negative
power, make the wire pass through the annealing capstans with
current, by short-circuiting, to preheat, anneal and dry.
4-3. The annealing current and voltage, by auto tracking the
drawing speed to auto adjust.
4-4. To cooling fast to achieve the annealing, the annealing
capstan is under the cooling water. There is a cooling tank at the
bottom of the machine, cooling water, better use fat content of
0.5% emulsion. The pump shall pump the cooling water through the
pipe and the switch to the annealing door. Adjust the cooling water
switch to make sure the water is in certain height.
4-5. To make sure the wire while annealing, no Oxidation, there is
a steam-in protection pipe, connect the pipe to the Steam
generator, to use the steam to protect the wire from the oxidation.
4-6. In the exit of the drying section, there is a blowing device.
In the device, shall have two dies. Connect the air compressor to
the air compress input pipe, then out by the blowing device, adjust
the switch, to make all the left water of the drying part, on the
surface of the wire, blow away.
V. Advantage and After-sale service
A: Advantage
(1). HENGXIE has some world famous parts suppliers, has special
lubrication system for the gears and bearing.
(2). Body and other key components and parts are produced by our
own factory , quality is reliable.
(3). Our company’s developing process in more than 10 years.
(4). DC. three-section annealing
B: After-self service
Our company for all machine product, since the shipment date, our
company free after sale maintenance service guarantee period is:
(1) 1 year for mechanical part.
(2) 6 month for electrical part.
