HXE-24DW Fine copper wire drawing machine
24DW Fine copper wire drawing machine is used to drawing copper
wire from 0.6mm-1.2mm to 0.08mm-0.5mm.
II. Specifications
1. Inlet wire diameter: 0.6mm-1.2mm. Outlet wire diameter:
0.08mm-0.5mm. Speed: 2500mpm, Capacity: 0.2mm, 30kg/h; 0.3mm, 37kg/h; 0.4mm,
46kg/h; 0.5mm, 52kg/h. Dies number: 24. Slip ratio (Area reduction) : 13%+ 8%.
2. Wire drawing mode: horizontal-mode and 4 axes. Driver: by dual Inverters control, Brand: Inovance,Chinese famous
brand, 15kw+3.7kw. Main motor: 15KW AC 3 phase motor. Spooler motor: 3.7KW AC 3 phase motor.
3. Motor brand: Wan Nan motor, China classical brand. Capstan: Ceramic plasma. Max capstan diameter: 242mm. Max fix speed capstan: 207mm. Machine structure: Cast iron. Reverse system: PID synchronous control spool.
4. Transmission: Flat belts. Pay-off method: Over-head. Tension control: Weight balance by swing arm
Lubrication type: spray, Grade 2.5%-3%, Capacity 40L/min, Bobbin size: 300mm, material steel, 17kg.
Take up: Shaft type.
5. Bobbin capacity: 50-60kg/max. Brake: Magnetic brake. Power source: Customize. Machine dimension: L2550mm*W1600mm*H1590mm, Machine weight:
2500KG
III. Advantage and after-sale service
A: Advantage
(1) HENGXIE has some world famous parts suppliers, has special
lubrication system for the gears and bearing.
(2) Body and other key components and parts are produced by our own
factory , quality is reliable.
(3) Our company’s developing process in more than 10 years.
B: After-sale service
Our company for all machine product, since the shipment date, our
company free after sale maintenance service guarantee period is:
(1) 1 year for mechanical part.
(2) 6 month for electrical part.
Under these situation mentioned, the Seller will not take
responsibility, but if the Buyer agree, will charge fees
accordingly to repair the machine.
A. Due to wrong operation while shipping.
B. Due to Buyer`s wrong preparation that may cause damage to the
machine.
C. Due to Buyer`s wrong operation that may cause damage to the
machine.
D. Not in the consuming part list.
E. After agreement are made for the shipping, for any damage, Buyer
should inform Seller in letter form to repair in seven days, If
beyond the dare, Seller shall take no responsibility.
F. For any other failures due to acts of God (such as lightning,
typhoon, earthquake, riots, war, fire or flood) and other factors
that will cause damage, Seller shall take no responsibility.
G. Seller guarantee provide long term support regarding the parts
and teach. After warranty, will charge accordingly.
IV. Components
| Name | Quantity |
| 1. Pay-off shelf | 1 set |
| 2. HXE-24DW Fine copper wire drawing machine | 1 set |
| 3. Bobbin Unloading device | 1 set |
| 4. Spare parts | As per List |
| 5. Operation manual | |
V. Installation, Lubrication, Through the dies
1. Installation
The machine should be installed in the flat clean, well-ventilated
ground, shock-absorbing rubber block on the base of the machine,
placed by horizontal correction.
Use the foundation screws to fix the four sides of the machine on
the ground to ensure that the machine is in operation, no vibrate.
Electrical control box RST terminal for the external power cord,
ground wire terminal must be grounded.
2. Lubrication
2-1. Ensure that the lubrication oil temperature control in the
range of 40 -50 ℃ or lower.
2-2. Use special Silver lubrication oil to protect the wire.
3. Through the dies
3-1. Use pliers to break the wire to get a smaller section.
3-2. Use pliers to make the wire through the dies, then pull the
wire out. Pay attention to the dies` front and back.
3-3. If wire breaks can use Cold welding machine to fix.
