0543 Nass Type System 13 30mm Copper Wire Solenoid Magnet Coil
The 5043/5045 solenoid coil is an important part of the electronic
drain valve, and the automatic timing of the drainage effect is
achieved by the control of the solenoid coil and the timer. The
electronic drain valve is matched with the solenoid valve by the
analog circuit solid-state electronic timer to realize the
automatic discharge of the condensed water of the compressed air
system. Electronic drain valves are widely used in compressed air
system components such as filters, separators, dryers, gas storage
tanks, and drip feet. The discharge time and interval can be
adjusted according to different needs. Install the electronic drain
valve. Note that the direction of the arrow on the valve body
should be the same as the direction of flow of the condensate. The
electronic drain valve can be installed in any position. A
container should be placed at the outlet of the valve to collect
the condensate. It can also be achieved by placing the tube, but be
careful not to use a hose that does not resist when the valve is
opened.
What is a solenoid?
Solenoid is the generic term for a coil of wire used as an
electromagnet. It also refers to any device that converts
electrical energy to mechanical energy using a solenoid. The device
creates a magnetic field from electric current and uses the
magnetic field to create linear motion. Common applications of
solenoids are to power a switch, like the starter in an automobile,
or a valve, such as in a sprinkler system.
How a Solenoid Works
A solenoid is a coil of wire in a corkscrew shape wrapped around a
piston, often made of iron. As in all electromagnets, a magnetic
field is created when an electric current passes through the wire.
Electromagnets have an advantage over permanent magnets in that
they can be switched on and off by the application or removal of
the electric current, which is what makes them useful as switches
and valves and allows them to be entirely automated.
Like all magnets, the magnetic field of an activated solenoid has
positive and negative poles that will attract or repel material
sensitive to magnets. In a solenoid, the electromagnetic field
causes the piston to either move backward or forward, which is how
motion is created by a solenoid coil.
Technical parameter of electronic drain valve solenoid coils:
| Model No. | BB14542004 |
| Normal voltage | DC12V/DC24V/AC110V/AC220V; or OEM |
| Normal power | AC:22VA; DC:13W 20W |
| Insulation class | H |
| Connection type | DIN43650A |
| Application | Electronic drain solenoid valves accessories coils |
| Weight | 160.5 g |
| Hole size | 14 mm |
| Height | 42 mm |
| Width | 29 mm |
Main dimension of 5043/5045 solenoid coils for water electronic
drain valve:
Detail enlargement of 14 mm Inside Hole 42 High electric solenoid
coils:
Connection of AC220V/DC24V black electromagnetic coils in
electronic drain valve:
In the process of using the electronic drain valve, the following
points should be noted:
1. Before installing the drain valve, it is preferred to remove the
sludge, copper scrap, rust, etc. from the compressed air system. It
is recommended to drain the system for 3-5 minutes under full
pressure before installing the drain valve.
2. The direction of drainage is the same as the direction of the
arrow on the valve body.
3. The supply voltage should be consistent with the drain valve
voltage (the drain valve voltage is marked on the coil). Do not
connect the wrong power supply.
4. The test membrane switch on the timer is a manual test button.
Each time the button is pressed, the drain valve is discharged
once. This button is used to check the drainage condition at any
time in daily work.
5. The two knobs of the timer are used to adjust the discharge and
interval time. The user should adjust the time according to the
climate and working conditions.
6. In addition to the connection function, the small screws on the
drain valve junction box have the function of pressing the seal to
prevent water from entering the timer and the coil, so be sure to
tighten. Otherwise, the gasket will not be waterproof, which will
cause the coil. And the burning of the timer. The lock nut of the
terminal is also waterproof, so be sure to tighten.
7. When the electronic drain valve is in use, the solenoid valve
may not be tightly closed, which is always leaking. Usually the
fault is not caused by the quality of the drain valve itself. The
reason is that the condensate is too dirty, and the tiny solid
particles in it Enter the valve plug and catch the valve plug.
Welcome to your inquiry!
