ASCO Type 238310-004-D 12VDC 238710-006-D 24VDC Red Hat
Electromagnetic Solenoid Coil
Pulse Valve Solenoid Coil burnout detection method:
The reason why the pulse valve does not work may be: the power
supply is cut off or the cleaning controller is out of order, the
pulse valve of the pulse dust collector has debris, the air leaks
all the time, the pulse valve coil burns out, and the compressed
air pressure is too low.
Remedy: Restore power or repair the cleaning controller, carefully
clean the pulse valve, change the pulse valve coil, check the
pneumatic system and compressor.
Use the multimeter to measure the resistance of the attracting coil
and the holding coil separately. The resistance of the attracting
coil is generally below ohms, while the resistance of the holding
coil is generally around 1 ohm. If the multimeter pointer does not
swing, that is, the resistance is infinite, indicating that the
line is open; if the resistance is less than the specified value,
the line is short-circuited. If the wire is broken or shorted, it
needs to be replaced.
What problems occur when the solenoid valve coil is in use?
Everyone knows that solenoid valves play an important role in
industrial applications, and they have a long running time, and
sometimes there are some problems that make the equipment not
function properly. Most of this problem is caused by improper use
of the solenoid valve coil.
The solenoid valve coil may not be very secure at the time of
installation. During the operation of the device, the coil is in a
strong operation, so that the coil will fall, the solenoid valve
will not operate normally, or some may fall, and some may not. It
may cause the device to work for a while and not work properly,
both of which will delay the work. At this time, the operation is
relatively simple, and the coil can be firmly fixed on the solenoid
valve. There is also a case where the solenoid valve coil may be
burnt out due to excessive voltage, and the device may not operate
normally.
Therefore, when using the solenoid valve later, be sure to check
the position of the solenoid valve coil and do the correct
operation of the solenoid valve coil. This will ensure that the
solenoid valve will not cause problems.
Dimension of BB14439333 Solenoid Valve Coil :
Technical Data:
Solenoid Coil Production Line:
Attention:
1. This air suspension compressor pump solenoid coil is made of
high quality components.
2. Replaces the original air compressor solenoid coil of your car
and equal the original quality.
3. Please double confirm the compatibility as well as the OEM
number before purchasing.
4. Instruction is not included. Professional installation is
recommended.
Steps and methods for properly installing a solenoid valve coil:
1. Check if the solenoid valve and the selected parameters are the
same, such as differential pressure, etc. If the error occurs, the
solenoid valve coil will be burned out. Voltage fluctuations should
be within the normal range and meet the rated voltage.
2. Before connecting the pipeline, flush the pipeline and remove
the residual dirt in the pipeline. If there are residual stains, it
will affect the normal use of the solenoid valve. To prevent this,
a filter should be installed in the pipeline.
3. Install the solenoid valve coil of the solenoid valve vertically
on the horizontal and ground pipes. If there is a special
situation, it cannot be installed vertically. The appropriate
solenoid valve should be ordered in advance, otherwise the solenoid
valve will not work properly.
4. When installing, add a safety process and install a manual
cutting valve to facilitate maintenance in case of failure.
5. Pay attention to the direction when installing, can not be
reversed, installed in the direction indicated on the package, and
can be reversed in some special cases such as vacuum.
6. If the water may be damaged by the medium, you must take
appropriate protective measures or choose a solenoid valve with a
waterproof hammer function.
7. The solenoid valve cannot be energized all the time, otherwise
it will reduce its life. Note that normally open, normally closed
solenoid valves cannot be used with care.
Product Features:
1. Using high quality wire which has UL approved; 2. Using high
quality permeablity magnetic material which contain low carbon;
3. Using high quality housing material like PA66, PBT, PPS, BMC and
so on.
4. Insulation class can be B, F, H, N, C;
5. Protection class can be IP65, IP67 & IP69K;
6. We also offer special coils like ex-proof coils, water proof
coils and so on.
7. If you have special requirement, pls feel free to contact us.
Focus on your demands, Offer you best solution:
√ Contact us if some points you have doubt
√ Contact us if somewhere need to change
√ Contact us if not the one you are looking for
√ Contact us if you are doing designing
Welcome to your any question and inquiry!
