DC12V Solenoid Coil For AEB 2386310000 / 2386370000 / 2386350000
Injectors Rail
This 12VDC solenoid coil is applied in AEB Type 2386310000 /
2386370000 / 2386350000 Injectors Rail. Gasoline car injection
solenoid valve structure is mainly composed of external solenoid
valve coil, c-type magnetic guide plate, fixed iron core, cylinder,
spring, valve core, valve seat and air outlet. The drive circuit is
used to control the fast closing of electromagnetic circuit. The
reverse spring force of the spring closes quickly to allow high
speed operation to control the injection of gas fuel. Automobile
solenoid valve is the actuator of electronic control system. If the
solenoid valve is running, but the solenoid valve is working, there
are certain conditions. If it rings all the time, it may indicate
that the solenoid valve is damaged or malfunctioning.
Technical parameter of AEB Type Injectors Rail Solenoid Coils:
| Model No. | BB18923801 |
| Normal voltage | DC12V (±10%) |
| Normal power | DC: 62Watt |
| Material | Brass, Plastic |
| Wire class | H |
| Connection type | The vehicle uses electricity the group of lines connector |
| Application | AEB 2386310000 / 2386370000 / 2386350000 Injectors Rail |
| Hole size | 12 mm |
| Height | 29 mm |
| Width | 31 mm |
Main dimension of Solenoid Valve Coil For AEB Type Injector Rail:
Detail enlargement of Solenoid Valve Coil For AEB Type Injectors
Rail:
Applied in AEB 2386310000 / 2386370000 / 2386350000 Injectors Rail:
Production display of DC12V Solenoid Valve Coil For ABE Type
Injector Rail:
More details about Solenoid Coil For AEB 2386310000 / 2386370000 / 2386350000
Injectors Rail in below Youtube Video:
Production details of Electromagnetic coil:
A solenoid coil is made by prepreparing the prepared skeleton onto
the shaft of an automatic winding machine. According to the
programming, that is, the number of windings, start the winding and
remove the winding. After welding treatment, test resistor
qualified, put into a drying box for drying. The drying temperature
is controlled at about 80 degrees, and the drying time is over 4
hours. For all solenoid valve coil manufacturers, the above steps
are basically the same.
The most critical part below is sealing the dry coil. There are
three plastic sealing methods on the market, one is ordinary
thermoplastic polypropylene PP plastic; The second is thermosetting
DMC unsaturated polyester fiber reinforced plastic, and the third
is thermosetting epoxy resin molding plastic packaging, the first
is common plastic is not recommended for users to use, because this
product packaging products will be short-circuit or decomposed into
a long period of time, mainly PP material and skeleton material
together. Water entering the air will not meet the requirements of
the cooking test. The second method can meet the requirements of
water immersion test, but does not meet the requirements of cooking
test. What is cooking test is to put the product into 100 boiling
water boil for 2 hours, quickly put in cold water for 1 hour, then
put in boiling water for 1 hour, and then put in cold water for 1
hour, the surface water is blown off, waveform and day waveform
table superposition. The measurement will not short circuit. Third,
it has excellent electrical insulation, high dielectric strength,
heat resistance, corrosion resistance, flame retardancy, forming
the heat resistance of the index is 1500 degrees, good mechanical
strength, high dielectric properties, resistance to leakage) arc
resistance, suitable for use with different ions, or in the
environment of corrosive gas, items can be exposed outdoors for a
long time.
Welcome to your any question and inquiry!
