HXE-14DH Copper wire drawing machine with large spool
I. Machine overview
This machine adopts programmable controller and dual inverters, the
sliding and automatic speed control and variable speed. With energy
Low consumption, high reliability, small slip rate, long life,
large capacity of take-up, low noise, nice shape, etc.Machine is
operation simply, safe, reliable, and easy maintenance. In order to
make the user familiar with and master the rules, please users read
this manual carefully before using.
II. Components
| Name | Quantity |
| 1. Pay-off stands | 1 set |
| 2. HXE-14DS Drawing machine | 1 set |
| 3. Spare parts |
III. Parameters
(1) Inlet : ф1.6mm/max copper; ф2.5mm/max aluminum
(2) Outlet: ф0.25-ф0.65mm; ф0.4-ф0.8mm
(3) Mechanical speed: 800MPM/MAX
(4) Dies: 14 (buyer-owned) Max
Dies: 7 (buyer-owned) Minimum
(5) Dies OD: ф25mm X 8 - 12mm thick
(6) Slip ratio: 1 -13, 15%;14, 8%
(7) Main motor: AC15.5KW motor
(8) Take-up motor: AC7.5KW motor
(9) Take-up diameter: ф400 - ф500
(10) brake: pneumatic brakes
(11) Power consumption:15-30kw power
(12) Lubrication capacity: 150L/MIN
IV. Note
1. to achieve the requirements of this specification, the cable
must be reasonable, good Lubricating fluid, good Dies, and
high-quality copper wire.
2. not used the reel without balancing requirement.
Electrical system normal conditions are as follows:
A. Environmental temperature: -10 ℃ ∽ +40 ℃ (no freezing
conditions), a 24-hour period, the average temperature does not
exceed +35 ℃.
B. atmospheric conditions: air, harmless dust, corrosive and
explosive gases.
C. Relative humidity: +40 ℃ when the maximum temperature does not
exceed 50%, a lower temperature allows a higher relative humidity
of 85% at +20 ℃.
D. Altitude: not more than 1000M, more than 1000M, specified in
accordance with this.
Elevation m | Correction facto |
| Current | Withstand |
| 1000 | 1 | 1 |
| 1500 | 0.99 | 0.95 |
| 3000 | 0.96 | 0.80 |
| 6000 | 0.90 | 0.56 |
E. Power supply voltage: sinusoidal, three-phase four-wire 380V,
50HZ; voltage fluctuation range does not exceed the rating of ± 5%,
should ensure that output ratings; voltage fluctuations not
exceeding ± 10%, should ensure reliable operation ; frequency
fluctuations should not exceed the rating of ± 2%.
F. Install inclination: Vertical mounting installation inclination
should not exceed 5%.
V. Advantage and after-sale service
A: Advantage
(1). HENGXIE has some world famous parts suppliers, has special
lubrication system for the gears and bearing.
(2). Body and other key components and parts are produced by our
own factory , quality is reliable.
(3). Our company’s developing process in more than 10 years.
B: After-sale service
Our company for all machine product, since the shipment date, our
company free after sale maintenance service guarantee period is:
(1) 1 year for mechanical part.
(2) 6 month for electrical part.
Under these situation mentioned, the Seller will not take
responsibility, but if the Buyer agree, will charge fees
accordingly to repair the machine.
A. Due to wrong operation while shipping.
B. Due to Buyer`s wrong preparation that may cause damage to the
machine.
C. Due to Buyer`s wrong operation that may cause damage to the
machine.
D. Not in the consuming part list.
E. After agreement are made for the shipping, for any damage, Buyer
should inform Seller in letter form to repair in seven days, If
beyond the dare, Seller shall take no responsibility.
F. For any other failures due to acts of God (such as lightning,
typhoon, earthquake, riots, war, fire or flood) and other factors
that will cause damage, Seller shall take no responsibility.
G. Seller guarantee provide long term support regarding the parts
and teach. After warranty, will charge accordingly.
