|
|
| Models / ordering information 230/1500 230/1500 230/1500 115/750 115/750 115/750 220/1200 220/150 220/0 220/600 220/75 220/0 |
| Part number 241123.140 241123.141 241123.142 241123.140L 241123.141L 241123.142L |
| AC OUTPUT DATA |
| Voltage (default) / (adjustable range) 230 VAC / 200 - 240 VAC 115 VAC / 100 - 127 VAC |
| Frequency (default inverter mode) 50 Hz (adaptive) 60 Hz (adaptive) |
| Frequency (set-able inverter mode) 50Hz, 60Hz or last synced 50/60Hz (adaptive), 94-106Hz6) |
| Power maximum (continuous / overload (<15s) ) 1200 W (1500 VA) / 2000 VA 600 W (750 VA) / 1000 VA |
| Load sharing ±5% of active power from 10 to 100% load |
| Current maximum (continuous / overload (<15s) ) 6.5 ARMS / 8.7 ARMS |
| Current (maximum) Quick trip (20ms) 32 A (6 x nominal) |
| THD < 1.5 % at resistive load |
| Protection Fuse in L, Hot pluggable, Varistor |
| DC OUTPUT DATA |
| Voltage (default) / (adjustable range) 245 VDC / 194 - 290 VDC |
| Power (maximum @nominal input) 1200 W 1) 150 W 0 W 2) 600 W 1) 75 W 0 W 2) |
| Current (maximum @VOUT ≤ 216 VDC) 5.56 A 1) 0.69 A - 2.78 A 1) 0.34 A - |
| Hold up time, maximum output power >10ms; VOUT > 190 VDC (only in rectifier mode) |
| Current sharing (10 - 100% load) ±5% of maximum current from 10 to 100% load |
| Static Voltage regulation (10 - 100% load) ±0.5% |
| Dynamic Voltage regulation ±5.0% for 10-90% or 90-10% load variation, regulation time < 50ms |
| Ripple < 1 VPP , 30 MHz bandwidth |
| Protection Short circuit proof, Over voltage shutdown, Reversed polarity and Fuse |
| INPUT DATA |
| AC Mains Input Voltage (range / LV disconnect) 185 - 275 VAC / 170 VAC 95 - 140 VAC / 85 VAC |
| AC Current (maximum) 11.5 ARMS 9.1 ARMS 3) 8.2 ARMS 3) 11.3 ARMS 10.1 ARMS 3) 9.2 ARMS 3) |
| Frequency (default: sync range) 47-53 & 57-63 Hz 47-53 & 57-63 Hz |
| Frequency (set-able: sync range) 47-53 Hz, 57-63 Hz or both (adaptive) |
| Power Factor / THD > 0.99 at 50% load or more / < 3.5% |
| AC Input Protection Fuse in L and N, Hot pluggable, Varistor |
| DC Voltage nominal / extended range4) 204 - 290 VDC / 180 - 204 VDC |
| DC Current (maximum) 6.67 A / 9 A during overload (15s) 3.2 A / 4.5 A during overload (15s) |
| OTHER SPECIFICATION |
| Efficiency >96% (mains mode (AC/AC and AC/DC)), >94% (inverter mode (DC/AC)) |
| Isolation 3.85 kVDC - ACIN/OUT to PE, 3.55 kVDC - ACIN/OUT to DC, 4.25 kVDC - ACIN/OUT to CAN/SYNC, 2.2 kVDC- DC to PE, 3.5 kVDC - DC to CAN/SYNC |
| Alarms: Red LED Low and high mains input voltage shutdown, High and low temperature shutdown, Rectiverter Failure, Alarm relay [NO max 75 VDC / 100 mA] Overvoltage shutdown on output, Fan failure, Low output voltage alarm, CAN bus failure, Sync bus (AC output OR DC output alarms) lost and Sync fail |
| Warnings: Yellow LED Rectiverter in power de-rate mode or in power or current limit mode on DC or AC port, Remote output current limit activated, Loss of CAN communication with controller |
| Normal operation: Green LED AC output and/or DC output on and ok |
| Operating temperature -40 to +75°C (-40 to +167°F), humidity 5 - 95% RH non-condensing |
| Temperature de-rating above 55°C (131°F) 1200W to 480W @ 75°C (167°F) for each, AC and DC, outputs (total power 2000W to 800W) |
| Storage temperature -40 to +85°C (-40 to +185°F), humidity 0 - 99% RH non-condensing |
| Dimensions[WxHxD] / Weight 109 x 41.5 x 327mm (4.25 x 1.69 x 13”) / 1.95 kg (4.3 lbs) |
| DESIGN STANDARDS |
| Electrical safety EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013, IEC/EN 62040-1:2008+A1:2013 UL 60950-1:2014, UL1778:2014, CSA C22.2 No. 107.3-14 |
| EN 61000-6-1:2019, -6-2:2019, - 6-3:2007 + A1:2011, - 6-4:2019, IEC 61000-6-5:2015 EMC EN 62040-2:2006 (C1 emissions, C2/C3 immunity), FCC CFR 47 Part 15 EN50121 -2:2017+A1:2019, -4:2016+A1:2019, -5:2017+A1:20195) |
| EU 2015/863 (RoHS) & 2012/19/EU (WEEE) / ETSI EN 300 019: 2-1 (Class 1.2) & 2-2 (Class 2.3) Environment Normal operating conditions as per IEC 62040-5-3:2016 clause 4.2. Other operating conditions as per IEC 62040-5-3:2016 clause 4.3, must be advised |
| 1) AC load has priority. Maximum available DC output power and current is dependent on 3) If DC port is overloaded pulling the voltage below 194V the input current may increase above this level. instant AC load and AC input voltage; i.e maximum 800W/7.4A at full AC power and nominal 4) Reduced performance - no over load support, and for 200 - 240 VAC output THD will increased and maximum input for 230VAC. output power de-rates (to 970W for 230 VAC @ 180 VDC) 5) to meet surge requirement of 4kV external surge 2) DC port must still be considered bi-directional port; voltage will present if mains powered protection is needed on AC ports 6) required FW version ≥ 1.10/1.10 |
